Among its products is the power transducer. The product is an electrical isolation transducer of single-phase active and reactive power measurement, complete isolation between input and output signals. It is designed to measure power, reactive power and power factor. The product is widely used in electricity, communications, railways, industrial control and other fields. The transducer weights 0.7-pound, 1-500-volt, 0.5-700 A, the size is 76mmx32mmx2inch. The response time of the transducer is 250 ms. (a) 1. What is the volume of the transducer in cubic m? 2. How many transducers can be packed in box of 1m X 0.5 m X Qm? 3. If the factory produces 500 transducer per hour, how many minutes are needed to produce 50 kg of the transducer?

Among its products is the power transducer. The product is an electrical isolation transducer of single-phase active and reactive power measurement, complete isolation between input and output signals. It is designed to measure power, reactive power and power factor. The product is widely used in electricity, communications, railways, industrial control and other fields. The transducer weights 0.7-pound, 1-500-volt, 0.5-700 A, the size is 76mmx32mmx2inch. The response time of the transducer is 250 ms. (a) 1. What is the volume of the transducer in cubic m? 2. How many transducers can be packed in box of 1m X 0.5 m X Qm? 3. If the factory produces 500 transducer per hour, how many minutes are needed to produce 50 kg of the transducer?

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter30: Dc Motors

Section: Chapter Questions

Problem 6RQ: What is CEMF?

See similar textbooks

Similar questions

What is CEMF?
A three phase full wave rectifier is shown below along with peak phase voltage Vm-169.7V. The load is purely resistive. The rectifier delivers Ipc = 100 A and the source frequency is 60 Hz. The DC output voltage is %3D VDc=280.7V and the output RMS voltage is equal to VRMS=280.93V. The efficiency, FF and RF are respectively equal to: Secondary D D D, R AD. Z D. D, Select one: O a. 99.83%, 100.08%, 4% O b. 99.83%, 55.08%, 4% O C. 99.83%, 100.08%, 16% O d. 87.83%, 100.08%, 4%
Identify the right statement relating to Zener impedance a. O b. O c. O d. the ratio of change of current to the change in input voltage in the breakdown region the ratio of change of voltage to the change in input power in the breakdown region None of the above the ratio of change of voltage to the change in input current in the breakdown region
A single-phase half wave uncontrolled rectifier circuit is operating with a purely inductive load and a source voltage of 100 sin (277t) V. An ideal PMMC ammeter is connected in series with the inductive load reads 20 A. Calculate the distortion factor of the rectifier. Answer Choices: a. 0.866 b. 0.707 c. 0.577 d. 0.816
Given the zener voltage at 9V and the zener power at 1W, what is the range of allowable values of Iz (operating values). a) 0.11A b) 22mA to 89mA c) 9A d) 0.11A to 9A
An FWR using a centre-tapped Transformer Supplies an average voltage of 120V to a 250 kΩ load Calculate (a) the peak value of output voltage (b) The required Transformer secondary voltage (rms value) (c) Average Current delivered to load (d) Average current through each of the diodes. (e) Peak Current through each of the diodes (f) PIV requirements for each of the diodes. AC supply voltage is 230V and assume ideal diodes.
A load is connected in the Full Bridge rectifier circuit (Four Diodes). Usedtransformer primary voltage value is 220 V (rms). The transformer winding ratio is 1:10.Using the 0.7 V model of the diode,Load Value: Student No. Last 1 digit ( will be selected as kΩ, LastThose whose number is "0" get "9")a) How many % of conduction does each diode branch stay on?b) Find the average values of the load voltage.c) Find the average values of the load current.d) Find the effective value of the load voltage.e) Find the effective value of the load current.
advantages of combination circuits
The input to a full-wave rectifier is 10 V AC (RMS). The load resistor is 10 ohms. The DC voltage at the output is:
what is the use of DC/DC tension converter DC/DC booster MT3608
The input to a full-wave rectifier is 30 V AC (RMS). The load resistor is 10 ohms. The DC power at the output is: O A. 73 W O B. 18 W C. None of the other choices are correct D. 36 W O E. 146 W
Compute the V2(peak) Half of 2nd windings, Vout(peak), Vout(DC), fout in the center tapped rectifier circuit below: Note: The table shows the values measured using Multisim 10 application