All the options are given in KN and KN/m wherever applicable. Point A is pin support and point D is roller type support. Uniform horizontal load of 78KN/m is acting on beam AB while concentrated load of 136KN is applied at BCD. AB= 5m, BC=CD= 2m. What will be the bending moment in KN-m at joint B? Include (-) sign if negative moment. Express your answer in 2 decimal places. W wm A 4m 3m U

All the options are given in KN and KN/m wherever applicable. Point A is pin support and point D is roller type support. Uniform horizontal load of 78KN/m is acting on beam AB while concentrated load of 136KN is applied at BCD. AB= 5m, BC=CD= 2m. What will be the bending moment in KN-m at joint B? Include (-) sign if negative moment. Express your answer in 2 decimal places. W wm A 4m 3m U

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3. The beam ABCD is fixed with simple support of B and C as shown in the figure below. When point A is 15 mm and point D is bent upward by 10 mm, find the loads P, Q to make point A and D equal to point B and C support points. P is acting on point A, and Q is acting on point D. The Flexible Rigidity tee is 2.5 X 106 Nm (Use Maucalay's method) 15 mm B -2.5 m تے 5m 25m 25m 10 mm
For the truss shown below, P = 9.2 kips, a = 8 ft, and b = 6 ft. Determine the force in member 3 (tension is positive). Give the answer to one decimal place. 介。 Type your answer..
The steel is supported by the steel tie rod in AB beam B. Steel connection tension rod is placed 2 meters to the left of B and C sliding bracket is placed and P is loaded between AC It is. By ignoring the weights of beams and connecting rods, they can be determine the largest P load it can carry. The diameter of the BD rod is 16 mm. E = 200GPa I = 150x(10^6)mm^4
a. The beam weighs 3600N. Draw the V and M diagram. b. Assume we do not know the weight of the beam the solid steel bar has a square cross section of side b and is supported as shown. We know that density of steel is 7860 kg/m, calculate the dimension b for which the maximum normal stress due to bending is 50 MPa. A C -1.2 m-1.2 m- D 1-1-1 B -1.2 m- b
The force in member AB of truss joint B shown in figure is given as 15 N B• - 10 N AB a. 10 N compression b. 10 N tension c. 15 N compression O d. 15 N tension
a. The beam weighs 3600N. Draw the V and M diagram. b. Assume we do not know the weight of the beam the solid steel bar has a square cross section of side b and is supported as shown. We know that density of steel is 7860 kg/m, calculate the dimension b for which the maximum normal stress due to bending is 50 MPa. C D I-KE -1.2 m-1.2 m 1.2 m B
In this figure, what is the force at member AD in kN?
A For the beam loaded as shown in figure, the location of point of contra flexure from the left end is L Wo B
The rigid beam shown is supported by a pin at A and two steel rods each of diameter 16 mm. If P = 30 kN, determine the tensile forces PBE & PCF in rods BE and CF, respectively. For steel, E = 200 GPa.
Determine the horizontal displacement of joint C. A L B The length, L, of trusses AC, BC is 1,500 mm. The applied force at joint C, is 8.0 kN. The cross-sectional area of both trusses, A, is 430 mm². The elastic modulus of truss AC, E₁, is 135 GPa. The elastic modulus of truss BC, E2, is 175 GPa. Enter your answer in mm to a precision of three decimal places.
The simply supported beam is built-up from three boards by nailing them together as shown. The wood has an allowable shear stress of tallow = 1.5 MPa, and an allowable bending stress of sallow = 9 MPa. The nails are spaced at s = 75 mm, and each has a shear strength of 1.5 kN. Determine the maximum allowable force P that can be applied to the beam. (Hint: There are three conditions.)
Solve using Moment -Area Method. The midpoint B of the steel cantilever beam ABC is supported by a vertical aluminium rod. Find the maximum allowable value of the applied force P if the stress in the rod is not to exceed 120 MPa. Use Est = 200 GPa, I= 50 x 10° mm* for the beam, Eal = 70 GPa, and A = 42 mm? for the rod. - Aluminum 5 m -Steel A C m m