Aliasing) An analog-to-digital converter samples a 20 Hz voltage sigmal at 100 samples/s. a. What is the frequency of the sampled signal? Is it aliased? b. Now suppose a second, 60 Hz signal, caused by line noise, is added to the original signal. To what frequency is this this line noise aliased? c. If the sampling rate is lowered to 50 samples/s, what frequencies are now present in the sampled signal? Power Supply width

Aliasing) An analog-to-digital converter samples a 20 Hz voltage sigmal at 100 samples/s. a. What is the frequency of the sampled signal? Is it aliased? b. Now suppose a second, 60 Hz signal, caused by line noise, is added to the original signal. To what frequency is this this line noise aliased? c. If the sampling rate is lowered to 50 samples/s, what frequencies are now present in the sampled signal? Power Supply width

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Identify the given statement. FM and PM demodulators can actually reduce noise and increase the signal-to-noise ratio during the demodulation process by using limiters. This is known as the capture effect. Select your answer. The statement has no fixed information. The statement is false. The statement is true. The statement is a case-to-case basis.
Which statement is true? a. In FSK, the modulating signal and the carrier signal are both analog b. In FSK, the modulating signal and the modulated signala re both digital c. In FSK, the modulating signal and the modulated signal are both analog d. In FSK, the carrier signal is analog and the modulating signal is digital
B- An rate. analog signal having single frequency as 3 kHz is sampled with 5 kHz S Describe its frequency spectrum. What will be the output if the sampled signals a passed through a low-pass filter having cutoff frequency at 2.5 kHz? signal. are sent in the analog
A) what name the modulation scheme in the blue curve in A and C B) what is the duty cycle in B C) What is the sampling Frequency in B D) write and equation that represent the modulated signal in B solve all parts or will dislike
5. A signal is expected to have a frequency of fm 1000 Hz. (a) (b) (c) signal? What minimum sampling frequency is required in order to accurately measure this What frequencies would be experimentally observed if the signal were sampled at 1500 Hz? Show the folding diagram and label it up to 4500 Hz. At what frequency would the signal, fm 1000 Hz, be observed as if sampling at 1500 Hz? Also list and show on the folding diagram, the lowest four frequencies that would be aliased and also observed at the same alias frequency as the expected signal.
A sinusoidal signal of 2 kHz frequency is applied at the input of a delta modulator with a step size of 0.1 volt. The sampling rate of the delta modulator is 20000 samples per second. What will be the maximum amplitude of the sinusoidal signal if there is no slope overload distortion?
6. Consider the electrical circuits shown in figure a.) and b.). For each circuit determine the transfer function C/2 C12 2R 2R (a) R (b)
1. a) An analog signal contains frequencies up to 12 kHz. (i) What range of sampling frequencies dose allow exact reconstruction of this signal from its samples? (ii) Suppose that we sample this signal with a sampling frequency Fs = 9 kHz. Examine with proper diagram what happens to the frequency component F1 = 6 kHz after passing through the digital to analog converter. (iii) Repeat part (ii) for a frequency component F2 = 11 kHz. b) Why is it necessary to introduce an analog low-pass filter before analog to digital converter? Illustrate the fact with necessary diagram.
I'm designing a mixer in Qucs. What does input frequency range and input voltage swing mean? Is it the AC voltage source's frequency and peak voltage?
2. Sampling frequency is one of the important elements in signal processing. Describe the meaning of a sampling frequency using a sketch if possible. Why is it important to set the sampling rate higher than the maximum frequency measured?
a. In AC, how are the capacitors treated? b. In AC, how are DC sources treated? c. What is the amplifier configuration of Figure 4? d. What is the expected phase shift of the sinusoidal input at the output side? e. What is Zi across RG, the gate resistor? f. It is the IC in its smallest form. g. The most commonly used metal as interconnect of the chip to external peipheral. h. How is pin 1 of the chip determined? i. An IC package similar to a DIP but with the pins bent outward. j. Which sensors are packed as IC?
3. (a) The following figure depicts a sampled analog signal for digital signal representation. By applying the concept of Pulse Code Modulation, assume there will be 4-bit code words for each sampled amplitude. Calculate the normalized PAM value and normalized quantized value for the given analog signal value at different time stamps . Assume that the sampling amplitudes are between -32V to +32V. Time Analog Signal Value (V) -10.8 1 14.5 30.6 -21.7