Calculate the worst-case wall thickness between datum feature B and the 2-inch insidediameter in the drawing below:04.00.250.480.240O .500O .245Ø2.500-2.5400.000DABØ2.000-2.0100.010DABLA

Answered: alculate the worst-case wall thickness…

Engineering

Mechanical Engineering

alculate the worst-case wall thickness between datum featur ameter in the drawing below: Ø2.500-2.540 Ø2.000-2.01

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter3: Job Planning, Benchwork, And Layout

Section3.1: Understanding Drawings

Problem 9RQ: A dimension listed on an engineering drawing is known as the _______ _______.

See similar textbooks

Related questions

Q: c) What is the magnitude and direction (angle) of the acceleration?

A: Given Data The mass of the red tailed hawk is:m=1.1 kg The angle is:θ=60° The resistive force…

Q: Ex #1] Given a gear of 16 teeth, 4 diametral pitch. The dedendum equals 1/P, inch, the clearance is…

Q: 5.0.3 m³ of gas is filled in a closed tank at an initial condition of 2.75 bar and 40°C. The gas is…

Q: Steam at 400°C and 800 kPa enters a nozzle with a velocity of 10 m/s and leaves at 300°C and 200 kPa…

Q: 2) Compute the effective inertia that a clutch must transmit to accelerate a 54-inch solid shaft…

A: Introduction: The ability of a body to resist angular motion about an axis is defined as its moment…

Q: How are large tanks treated in fluid mechanics, conservation mass, conservation momentum and…

Q: Find the RN for a rectangular airplane wing with a span of 8 ft and wing area of 34 ft², moving at…

A: Givenspan length L=8ft=8×0.3048=2.4384 mwing area A=34 ft2=34×0.30482=3.1587 m2speed V=153…

Q: The solutions are hard to read. How to find Fh?

Q: Determine the products of inertia about the coordi- nate axes for the thin plate of mass m which has…

A: given; determine product of inertia? mass=mangle=βradius=a

Q: A 20-KW motor with 80% efficiency drives a centrifugal pump delivery 0.08m3/sec against a head of…

A: Introduction The efficiency of the pump consequently, is never more than a hundred percent since…

Q: Vertical turbines are to be used for flocculation in a water treatment plant with a design flow rate…

A: Solution: Given Data: Q=189270 m3/day=2.19 m3/std=25 min=1500 sG=70 s-1T=10oC

Q: The velocity of a particle is given by v= 20t²-70t - 289, where vis in feet per second and t is in…

A: Given, v(t)= 20t2-70t-289 ft/s

Q: - Calculate the specific volume, specific enthalpy, and specific internal energy of steam at (18)…

Q: 06) An air standard Otto cycle has a compression ratio of 7.5. The maximum and minimum cycle…

A: givenAn air standar otto cyclecompression ratio r=7.5Tmax=1600 KTmin=300 KPmin=100kPa

Q: Problem 3. A pump increases the water pressure from 70 kPa at the suction to 700 kPa at the…

Q: Determine the force P required to force the 14° wedge under the 92-kg uniform crate which rests…

A: Given : u = 0.34 P = ?

Q: Ex] A double-threaded right-handed worm gear transmits 15 Hp at 1150 rpm. The pitch of the worm is…

Q: Niagara Falls is about 50 m high. a. What is the temperature rise in kelvins of the water from just…

A: Given data:- Height of Niagara Falls =50 m To find :- Temperature rise of 1g water Energy produced…

Q: Member AB has the angular motions shown. Suppose that w = 4.5 rad/s and a = 6.7 rad/s². (Figure 1)…

Q: If the coefficient of friction between the steel wedge and the moist fibers of the newly cut stump…

Q: 1) Check that mechanism is kinematic chain: L B

Q: Air is enclosed by a rigid cylinder con- taining a piston. A pressure gage attached to the cylinder…

A: Introduction The temperature remains constant from the beginning to the end of the isothermal…

Q: Find the force in member AB D E 4m a. 4kN Compression b.2kN compression c. 2kN tension O d. 4kN…

Q: *6-64. Determine the force P required to hold the 150-kg crate in equilibrium.

Q: two steel plates are held together by two bolts. a)determine the required diameter of the bolts if…

A: For solution refer below images.

Q: A. A fluid at 100 psia, with a specific volume of 4ft³/lb and a velocity of 600 ft/s, enters a…

A: GivenP1=100psi=689.476kPav1=4 ft3/lb=0.062428 m3/kgV1=600 ft/s=182.88 m/sP2=20psi=137.895 kPav2=15…

Q: A motor winds the pulley at A with the kinematic quantities given. Find the acceleration of block E…

A: Given: To find: Acceleration of block E

Q: A ladder 10 ft long rests against a vertical wall. Let 0: angle between the top of the ladder and…

Q: 1. Space probes may be separated from their launchers by exploding bolts. (They bolt away from one…

Q: Consider a tube of inner and outer tadii ri and ro, whose temperatures are maintained at Ti and To,…

Q: 1) The freebody diagram of a supporting beam is shown below. 0.3 Ra F1 Đ 0.9 UDL- 1.5 -1.3 F2 Rb…

A: Detailed explanation and solution of the above problem uploaded in below pictures.

Q: A piston of double reciprocating pump running at 60 rpm to transport oil of 890 kg/m³. The pump has…

A: Given: The pump speed, N = 60 rpm The density of oil, ρ = 890 kg/m³ The stroke length of pump, L =…

Q: Ex] A double-threaded right-handed worm gear transmits 15 Hp at 1150 rpm. The pitch of the worm is…

Q: 3.42 Determine the Miller indices for the planes shown in the following unit cell: +2

A: Given

Q: What fiber fraction would be required for a composite with titanium fibers in a polycarbonate matrix…

Q: You place a 1.5 kg block of aluminum that is 45°C in contact with a 2.1 kg block 18°C. Both blocks…

A: Given data as per question Mass of aluminium block, mal=1.5 kg Temperature of aluminium block,…

Q: Calculate weight (Wgate) of the gate AB needed to keep the gate closed. Gate is 2 m wide.

A: Given:Width of gate, w=2 mPosition of point A from left side free surface, =2 mPosition of point A…

Q: Fully developed region Q Film fl P 12 a- b- 22₂ Pa Ha=0

Q: Current Attempt in Progress Determine the force P required to force the 14° wedge under the 73-kg…

Q: Air at T₁ = 20°C and P₁ = 100 kPa enters a compressor with a mass flow rate of m= 0.025 kg/s through…

Q: show me how you did it so I can understand, thank you. Pls answer both, this is my last tutor…

Q: The following figure shows a hollow piston of weight W-50 N and diameter D=3d occupies the position…

A: Given: The piston weight, W = 50 N The diameter of piston, D = 3d The diameter of lateral tube, d1 =…

Q: Devices can be combined to perform a variety of tasks. An adiabatic compressor, with air as the…

Q: I. How much heat will require to raise the temperature of a cube of ice (250 g) initially at -50 °C…

A: “Since you have asked multiple question, we will solve the first question for you. If youwant any…

Q: Build the following part. Report the volume in mm^3. Assume all dimensions are in mm. A = 44 B = 78

Q: using trendline, discuss relationship between temperature measured by thermocouple compared to…

A: Draw the given graph.

Q: Consider a person standing in a room with a temperature of 22°C throughout moment. It is observed…

A: Given Area, A = 1.4 m2 Temperature, T1 = 30oC T2 = 10oC…

Q: The vertical position of the 165-kg block is adjusted by the screw-activated wedge. Calculate the…

Q: Q6. Sketch the acceleration vector diagram for the engine mechanism below in fig.6, clearly…

Q: R15 -35- Ø10 -100 + -Ø20 R15 32 50

A: Given: There is a figure which has some circles and rectangle to draw. So the steps involved to draw…

Concept explainers

Basic Terminology in Mechanics

The area of science and mathematics concerned the motion of the objects, the relation between the force matter, and motion if specified. Forces exerted over the objects result in displacements or changes in the position of an object concerning its environment. This branch of physics keeps its roots in Ancient Greece in the form of the scripts of Aristotle and Archimedes.

Question

Calculate the worst-case wall thickness between datum feature B and the 2-inch inside
diameter in the drawing below:
04.00
.250
.480
.240
O .500
O .245
Ø2.500-2.540
0.000DA
B
Ø2.000-2.010
0.010DABL
A

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

7. Calculate the minimum wall thickness between the inside diameter and datum feature B shown in the figure below. Datum B @ LMC: Ø -Ø minus I. D. @ LMC: minus Tolerance @ LMC: - Ø. = The wall thickness equals half of the differences in diameters = Ø2.500 .020 4.059 +.003 Ø2.000 .020 +0.0200 ABO B A Unless otherwise Specified: .XXX= .010 ANGLES = ± 1°
7. Calculate the minimum wall thickness between the inside diameter and datum feature B shown in the figure below. Datum B @ LMC: minus I. D. @ LMC: -Ø. minus Tolerance @ LMC: - Ø = The wall thickness equals half of the differences in diameters = Ø2.500 .020 4.059 ±.003 Ø2.000 .020 0.0200 ABO B I A Unless Otherwise Specified: .XXX = .010 ANGLES = ± 1° Figure for Problem 7
Calculate the Resultant Condition of the HOLE in the drawing below: 1.000 O 1.060 O 1.000 O.530 .982 C 2.000 Ø.995-1.000 +0.008MABC 6.00 O None of these answers is correct X 3.000 Y 01.005-1.030 +0.005MABC B A XX = .01 ANGLES = ± 1°
Calculate the Minimum Y distance on the drawing below: 1.000 O 2.000 O .460 O .510 1.966 O .500 C 2.000 Ø.995-1.000 6.00 0.008 MABC 3.000 Y 01.005-1.030 +0.005MABC B A .XX = .01 ANGLES= ± 1°
Incorrect answer I've tried below (should be in inches) .0152 7.64*10^-3 .00556 29007 .0101 .0122
Find the volume described by 0srs 5,0s0S T/3, Os 0 s 21 a. 125T/3 O b. 251T/3 О с. 225T/3 O d. 215T/3
a) Create a sketch of the Figure 2 as below (.ipt) b) Extrude the sketch in a) by a thickness of 1mm (.ipt) Ø 25.40 25.35 6.50 X 3.25 KWY- 077 R92 30 ,6X R32 Ø73 HUB-Ø45 METRIC Figure 2
For the figure below, all dimensions in inch. A/The total Area: /The value of Y-bar is: the value of X-bar is: * 0.364 1.5 0.987 2.5 3.309 2.5 2.309 0.65 2.5 2.5 0.587 0.398 12.6 0.254 4.32 14 0.5 3.105 25.93 13.5 0.487 1.3 14.68 0.55 3.623 13.68 0.857 4 31 1.06 22.5 Other: 2.5 24 12 Other: Other:
Build the following part and report the volume in units cubed. A = 48 B = 51 R20 R10 B 30 50 2X R10 R20 Ø20 A 10 TYP DESIGN ERICS DRAWING TITLE
2. Make ten measurement for the diameter of the spherical ball first with vernier caliper, then micrometer. Then, fill the table with your results. Vernier Micrometer No. Caliper (mm) 6.05 6.05 (mm) 5.96 6.04 2 3 6.00 6.02 4 5.90 5.98 6.10 5.94 6 5.85 6.08 5.95 5.95 6.00 5.99 6.00 5.98 10 6.05 6.00 Determine average absolute deviation, sample standard deviation, sample variance and coefficient of variation for diameter measurement at Instruction 2 for both vernier caliper and micrometer.
If the pin in the drawing below is produced at Ø.498, what is its total positional tolerance? C 1.000 Y 1.000 .005 .500 .003 O .498 .007 Ø.515-.525 0.010MABC 1.000 B Ø.498-.500 0.005MABC A
Show the tolerance zone created by each of the given tolerance specfication. Superimpose the tolerance zone on the given drawing.