ACTIVITY 2: 1. A moist paper containing 20% water goes into the dryer in a continuous process. The paper leaves the dryer containing 2% water by weight. Calculate the weight of water removed from the paper per 100 lb of original moist paper.

Q: An oil burner nozzle is labeled 60°. This is the angle from straight ahead tothe direction that the…

A: Paper is placed 12 inches from the nozzle.  the oil burner is labeled at 600C, The Schematic of the…

Q: Q2: Fill the blanks 1- The processes that are changing the earth today are the same as they were in…

A: Answers for blanks are-

Q: Describe the difference between average pressure and false pressure

A: The force applied perpendicular to the surface of an object per unit area over which that force is…

Q: Match the type of calculation that must be used in determining the operating pressures of the…

A: The bubble point is the factor at which the first drop of a liquid combination starts to vaporize.…

Q: Is pinch point always located at the feed stage?

A: The location of the pinch point is to be mentioned.

Q: What is the difference between truncation error and stability?

A: To understand the answer to this problem knowledge of Process control systems is required. The given…

Q: Calculate the moles of a substance given the -number of particles.

A: The number of particles of a particular substance is given as, N = n×NA        (1) Here, N is the…

Q: D: Define and draw the Unit Cell and give an example.

A: A unit cell is the smallest element of a crystal lattice that indicates the three-d sample of the…

Q: Explain Process of extraction cooking oil about description and conditions process

A: Extraction is a process in which one or more components are separated selectively from a liquid or…

Q: 4. Draw the (211) plane on a standard set of x,y,z coordinates.

A: To visualize the (211) plane in a standard set of x, y, z coordinates, we can represent it as a 2D…

Q: Define the term, “measurement uncertainty”. Among the instruments below above, which ones  have the…

A: Every matter in the universe is measured in some quantities and also has some units. Measurement is…

Q: How is compressed gas released?

A: The compressed gases are hazardous while handling as the are stored under containers in very high…

Q: What is meant by the number of degrees of freedom?

A: The number of degree of freedom is to be defined.

Q: Calculate the following: Thermal conductivity of brass Calculated quantities Value Difference in…

A: Hi, thank you for posting the question. According to our guidelines, we are allowed to answer only…

Q: Recompute the answer into 4 decimal places

A: The given solution is: After substituting the value of CV, S , VCM and FC, the solution is obtained…

Q: For fractional distillation write explain and draw a schematic neat diagram with all labeled parts…

A: Fractional distillation is a type of distillation which involves the separation of miscible liquids.…

Q: Draw a graph and explain the variation of pressure drop with time in a compartmented baghouse.

A: To ensure the system's successful operation at all times, a variety of variables must be managed…

Q: Explain path line in relation to fluid mechanics.

A:

Q: If the distance between holes is 50 mm, the distance between the third spot light and the central…

A: Given data: Distance between hole is = d = 50 mm = 0.050 m distance between third spot light and…

Q: 2. List the most important pipe friction formula.

A: Introduction: The friction loss in uniform, instantly sections of pipe, called "major loss", is…

Q: you do it in another way especially the F and K part

A: The unit conversion is changing one set of units to an equivalent set of units. Both sets of units…

Q: Calculate the energy of a light wave with a wavelength of 730nm.

A: Given data arei Wavelength ˨=730 mm    Calculate energy E=?Concept used- Plank-einstein's equation…

Q: In mathematics, error tells the person how much correct or certain its measurement is. O True

A: To state whether the given statement is True or False

Q: The most widely used method for growing a single crystal silicon seed into a cylindrical ingot is: O…

A: We have to answer the most widely used method for growing a single crystal silicon seed to a…

Q: Q1/Is the system shown below under damping ? If yes ,determine the values of rise time, peak time,…

A: The given transfer function is; Gs = 10S(S + 3) + 20   (Eq. 1) Compare it with the standard second…

Q: Explain the friction between the mater (soled with soled, liquid with liquid)?

A: Motion: Motion is the phenomenon in which an object changes its position over time. Motion is…

Q: When using an aspirator as a source of vacuum in a vacuum distillation, do you turn off the…

A: It is to be mentioned if the aspirator is turned off before venting the system or not.

Q: What does a HYSYS fluids package represent thermodynamically

A: In chemical engineering, there are many calculations that can be done manually. But some are very…

Q: A mirror produces an image that is located 41.0 cm behind the mirror, when the object is located…

A: Given : The image distance, Object distance,

Q: A core sample is saturated with water, Weight of saturated sample in air is 22.5 g. Water-saturated…

A: Bulk volume of the sample is volume of the water trapped between the pores of the sample. The weight…

Q: Temperature measurement is done using a mercury thermometer; which is protected by a thermowell.…

A: The order of mercury thermometer is to be mentioned with detailed analysis.

Q: Please order the following apparatus in ASCENDING order of resolution; when comparing resolution,…

A: (1) Optical Microscope An optical microscope's highest resolution is about 0.2 microns (200 nm). The…

Q: a) A student is measuring the length of a wood. The reading from the measurement tape is 56.73 +0.02…

A:

Q: Locking out the circuit breaker prevents the accident switching of electricity. Select one: True…

A: Answer is True Locking out the circuit breaker prevents the accident switching of electricity is a…

Q: What is the most common method used to separate two fluid phases?

A: The most common method which can separate two fluid phases is to be mentioned.

Q: An ordinary garden hose sprinkler is sketched in Fig. 7.39. All the fluid enters at the axis (r ≈ 0)…

A:

Q: O O O O y form of iron-carbon system is Occurs below 7680C .a Magnetic b Occurs above 14100C .c…

A: correct property of γ form of iron-carbon system needs to be selected from given options.

Q: (b) Sketch the schematic diagrams of three characteristics stress-strain behaviors for polymeric…

A: The schematic diagram of the stress-strain behavior of a polymeric material is shown below:

Q: Distinguish between Newtonians and Non-Newtonians fluids with graphs and examples

A: Newtons Law of viscosity states that the shear stress between the layers of the fluid is…

Steady State Model

The steady-state model typically states that the entire universe is always enlarging, although it balances a fixed average density and matter that is being constantly generated to make new galaxies, star forms at a similar rate that the previous ones get indistinguishable due to the growing range and velocity of recession.