Activity 1: Determine the angle e for equilibrium of the lever shown in the figure. Disregard the weights of bars AB and BC. 2m 90 1m, A 200N 100N Activity 2: Determine the weight W and the horizontal and vertical components of the pin reaction at A for equilibrium assuming all bearings are frictionless. Beam AB weighs 600 KN. 800KN 400KN 3m 1m 2m 1600N/m Ap 6m

Activity 1: Determine the angle e for equilibrium of the lever shown in the figure. Disregard the weights of bars AB and BC. 2m 90 1m, A 200N 100N Activity 2: Determine the weight W and the horizontal and vertical components of the pin reaction at A for equilibrium assuming all bearings are frictionless. Beam AB weighs 600 KN. 800KN 400KN 3m 1m 2m 1600N/m Ap 6m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

for the beam shown in the figure, a) find the equation of elastic curve by integration method. b-) Draw (Ty), (mx) oliagrams of the beam. c-) find the Suppert reactions. 29=260 9=130 9-130 E L-158cm Figure: L=158 cm
w1 w2 P x1 x2 x3 e 50 32x 6 8 2258 Moment at A= w1 kN/m kN/m kN/m KN Im m m 20 deg Vertical Reaction at B = Vertical Reaction at C = x1 Horizontal Reaction at C = 3m kN-m Determine the Reactions at Fixed Support A, Roller Support B and Hinge Support C. ALL ANSWERS IN ABOSULTE VALUE AND IN THREE (3) DECIMAL PLACES INCLUDING ZEROS Vertical Reaction at A = KN Horizontal Reaction at A= kN KN KN B KN x2 W2 kN/m 2m P x3 Ꮎ 1m C
150 mm 60 mn 300 nm 000 m 50 mm 5 m B 25 kNm 5 m 10 KN A beam is created by nailing 3 planks together with 2 rows of nails as shown above. The beam exhibits a pin support at A and is suspended by a cable at B. A concentrated load of 10 kN is applied at the free end while a moment of 25 kNm is applied at location B. a) Determine the second moment of area (I) of the cross-section b) Draw the free body diagram, shear force diagram, and bending moment diagram of the beam c) For the maximum shear force on your SFD, determine the maximum and minimum shear stresses at the interface between the horizontal and vertical planks d) For the maximum shear force on your SFD, Determine the shear stress at the neutral axis
A load Pis supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 12200 ksi] rods, and a solid steel [E = 31000 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.72 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.54 in. Assune Ly=59 in and L2=89 in. If all bars are unstressed before the load Pis applied, determine the normal stresses in bronze rods (1) and steel rod (2) after a load of P = 16 kips is applied. (2) (1) L2 (1) |L1 O B C Answers: i ksi. i ksi.
The simply supported beam is subjected to the force F-550 N and the uniform distributed load with intensity w = 120 N/m. Draw the shear force and bending moment diagrams (in your homework documentation) and determine the equations for V(x) and M(x). Take z = 0 at point A. ру F Vc A wwwm k a b с 5.80 m 3.48 m 3.19 m Support Reactions The reaction at A is The reaction at Dis W a V(x)= In section BC: V(x)= In section CD: V(x)= Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value B N. N. Shear Force and Bending Moment Equations In section AB: N and M(x)= N and M(x)= b N and M(x)= 2013 Michael Swanbom 030 BY NO SA N-m. N-m. x N-m.
Question 1 Determine the reaction at B in kips on the beam shown. Assume A is a pin and the support at B is a roller (smooth surface). || A 500 lb/ft 7 ft B 4 ft
10. Determine the reaction at the roller support and draw the bending moment diagram for the beam and loading shown. The beam is W310X21 with E=190GPa and L=6m and load density of 2000N/m A DIOO ·L/2 L/2- IC -L12- B
Q1. (а) Figure Q1(a) shows a beam loaded with a point load and a partially UTM uniform distributed load. respectively. support at A and B are roller 3 UTM The M 5 UTM (i) Draw the free body diagram of the structure. * UTM UTM Determine the support reactions at A and B by taking the (ii) structure in equilibrium condition. ITM O UTM - UTM 5 UTM O UTM 30kN 30° 10KN/m F = 840 N 2m 24 m 2m 4m A \3 m G UTM 15 m 2 m STMUTM 5 UTM FIGURE Q1(a) 10 ni FIGURE Q1(b) 一

The overhang beam shown in Figure Q2 is pinned at A and rest on a roller at B. The beam supports a uniformly distributed load of A kN/m, a concentrated load of C kN and a couple of moment B kN.m a) Determine the support reaction at point A and B. b) Draw the shear diagrams of the beam. A=16 B= 24 c) 12 A kN/m A BkN-m -3 m- -3 m- -2 m- VC KN Figure Q2
Figure shows a statically determinate beam under distributed loading conditions where C is the constant. 2x x? q(x) = C(- L AB A 2L/3 L/3 RA RB Figure 2 a) Determine the resultant of the distributed load where C is constant. Submit part Unanswered b) The magnitude and direction of the reactions at support B. Submit part Unanswered c) The magnitude and direction of the reactions at support A.
8 kN 2 m -2 m 2 m 14 kN 6 kN DI RDH = A B C 28 kN-m 12 kN-m RA = Rov =' Solve for the following: a. What is the shear at C? b. What is the shear at D? c. What is the moment at B? d. What is the horizontal reaction at D? e. What is the horizontal reaction at A? f. Shear and Moment Diagram
Rigid AD rod in the figure, at points A and C with two vertical elastic bars articulated at the ends vertical from point D to P intensity while standing horizontal the force is affected. Elongation stiffness of ela stic bars EA and their length is L. According to this, a) The forcesthat will occurin the elastic bars, b) the displacement of the D point of the rigid bar, c) Calculate the support reaction at point B. EA,L A B D. EA.L rijit Fa + a 2a-