a.) In a drilling operation, 3 blind holes needs to be drilled to a depth of 16 mm and a diameter of 8 mm. The point angle is 105° and the drill is made from HSS material. The bench drill allows a fixed speed of 1400 RPM and a feed of 0.1 mm per rev. The work part is mild steel with a thickness of 22 mm. Determine the time required to complete this operation. b.) What are some factors that determine the type of industrial cleaning that will be applied to a part?

a.) In a drilling operation, 3 blind holes needs to be drilled to a depth of 16 mm and a diameter of 8 mm. The point angle is 105° and the drill is made from HSS material. The bench drill allows a fixed speed of 1400 RPM and a feed of 0.1 mm per rev. The work part is mild steel with a thickness of 22 mm. Determine the time required to complete this operation. b.) What are some factors that determine the type of industrial cleaning that will be applied to a part?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 0.4-inch diameter bit is used in a vertical or vertical drill that operates at 300 rpm. If the feed is 0.005 in / rev, what is the MRR? What is the MRR if the drill diameter is doubled? What is the power required in the drill if the material is an annealed AISI 1080?
What is the function of a drill bushing? In cases where a drill bushing is not used, how is the jig treated to guide the drill?
Find the machining time to complete the job as shown below from the basic raw material of 50 mm diameter and 100 mm length. Assume the following data: cutting speed for turning and boring = 25 m/min, feed for turning and boring = 0.5 mm/rev, cutting speed for drilling = 20 m/min, feed for drilling = 0.25 mm/rev, depth of cut not to exceed = 5 mm? 40 25 20 20 20 20
e) Explain the functions of drilling Stabilizers in drill string?
a. If rough milling of mild steel is performed using High Speed Steel (HSS) side and face milling cutter of 100 mm diameter, what rpm should be used. b. If finish turning of a shaft is done to reduce its diameter from 24 mm to 20 mm using carbide tool, what rpm should be used. Metric Surface Speeds in m/min (Cutting Speed) Tool Material Aluminum Drilling Carbide 90 - 115 Milling - Rough Carbide Milling - Finish Carbide 120 - 240 Turning Carbide Rough Carbide Finish HSS HSS HSS 55 - 60 120 - 240 150 - 270 75 - 105 60 - 90 60 - 90 135 - 180 Brass 40 - 45 75 - 100 45 - 60 60 - 75 90 - 210 105 - 210 135 - 260 35 - 45 55 - 75 60 - 90 75 - 105 60 - 100 Cast Iron 12 - 18 15 - 25 25 - 30 60 - 90 75 - 135 Mild Steel 10 - 15 75 - 105 75 - 120 18 - 27 18 -3- 45 - 60 23 - 40 100 - 145 Stainless Steel 8 - 18 25 - 37 10 - 15 55 - 67 12 - 25 85 - 150
17) A50-mm-dia endmill cuts 6061 aluminum with 30% tool engagement at a depth of 6 mm. The tool rotates at 200 rpm and is feeding at 250 mm/min. There are 2 teeth set at a rake angle of 10°. a. Calculate the required power of cutting. b. Determine the spindle torque. c. Determine the cutting force on each tooth. d. If the thrust force is measured to be 350N, estimate the tool-chip interface friction coefficient. How could you physically verify your power estimate?
A mild steel specimen of Initial diameter of 30.5 mm is turned to final diameter of 27 mm for an initial length of 153 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii)During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Time required to complete one single turning operation is 3.5 minutes (c) Spindle speed in in rpm (= (d) Cutting speed in m/minutes(=
What is the function of a drill bushing? In cases where a drill bushing is not used, how is the jig treated to guide the drill?
Which of the below is true for conventional milling: Chips are removed behind the cutter which reduces the chance of re-cutting Chip width starts from zero and increases which causes more heat to diffuse into the workpiece and produces work hardening O Creates cleaner shear plane which causes the tool to rub less and increases tool life
Drilling, diameter = 0.375 inches, feed is 0.003 inches/tooth, number of teeth is 2, rotation speed is 750 rev/min. Material is tough Copper alloy. Find: MRR, power at the motor, power at the tool, and torque at the tool. Work the problem in U.S. units and give the answers in U.S. units.
Determine the metal removal rate of a drilling process using 25 mm diameter twist drill, a cutting speed of 50 m/min and a feed of 0.2 mm/rev. Available drilling machine spindle rpm are: 300, 400, 500, 625, 750, 800, 900, 1000.
Solve