Concept explainers
INSTRUCTIONS:
I really need to understand this. Please follow and I'll give an upvote without any questions. Do not answer if you don't know, please I'm trying to study while working.
• If using calculator, please input at the solution. Example: "Just click at 'Mode 2 5" like that
• Always write the complete formula including derivation of the fomula
• When writing a formula, please input the exact word terminology. Example: Ia = Van/Zan where Ia is a phase A line current
• Always put explanation at the computation.
TOPIC: Analysis of Balance Polyphase Systems
QUESTION:
A. A delta connected load is supplied from a 230V, 3 phase abc system. The load impedances are Zab=10+j0, Zbc=5+j6 and Zca=5-j5, all in ohms. Find the current in line a in amperes.
Step by stepSolved in 2 steps with 1 images
- In step 2 you measured the voltage across each of the LEDs. This is their “forward voltage” that is referred to in the LED component page, which is the voltage required to light the LEDs. Notice that the combined forward voltage of D1 and D2 is greater than 3.3V, the LEDs will not light up at all. You should also have noticed that the forward voltage for one of the LEDS is lower than the forward voltage for the other LED. Some LEDS require less energy to light than others. Since D1 and D2 are in series, the same current will flow through each, but the different voltages across each LED reflect the different energy requirements. Finish each statement below, bears on this information and in the measurements you took in step 2 The measured forward voltage across D1 in this step is ________ The measured forward voltage across D2 in this step is ________arrow_forwardPLEASE ANSWER AS SOON AS. PLEASE SHOW ALL WORK PLEASEarrow_forwardWhat does this line of code do ? i++ O This is not allowed in Arduino language Adds 1 to the value stored in i Returns true if i has a positive value O None of the abovearrow_forward
- Please answer this question with as much details possible, so I can understand. This is for Electrical Engineering.arrow_forwardhow many free variables are in the system: a+b+c+d=1 a-b-c-d=2 and please explain how you got the answerarrow_forwardINSTRUCTIONS: I really need to understand this. Please follow and I'll give an upvote without any questions. Do not answer if you don't know, please I'm trying to study while working. • If using calculator, please input at the solution. Example: "Just click at 'Mode 2 5" like that • Always write the complete formula including derivation of the fomula • When writing a formula, please input the exact word terminology. Example: Ia = Van/Zan where Ia is a phase A line current • Always put explanation at the computation. TOPIC: Analysis of Balance Polyphase Systems QUESTION: A phase voltage of 230V, 3 phase supply feds a balanced wye-connected load of 10+j5 ohms per phase. The real power of the load is _____ watts.arrow_forward
- Resistor Rx in the Wheatstone bridge in the picture is a wire strain sensor. The battery voltage is UB = 68 V. The value of the three resistors is as follows: R1 = 1 . R 2 = 1 . R3= 1800 . a) Determine the sensor resistance if the instrument shows no potential difference b) The current from the battery branches to I1 through resistor R1 and I2 through resistor R2. Determine the ratio (ratio) between the current I1 and the current I2arrow_forwardINSTRUCTIONS: I really need to understand this. Please follow and I'll give an upvote without any questions. Do not answer if you don't know, please I'm trying to study while working. • If using calculator, please input at the solution. Example: "Just click at 'Mode 2 5" like that • Always write the complete formula including derivation of the fomula • When writing a formula, please input the exact word terminology. Example: Ia = Van/Zan where Ia is a phase A line current • Always put explanation at the computation. TOPIC: Analysis of Balance Polyphase Systems QUESTION: A 208V, 3 phase power system is connected through a three-phase transmission line to a Y-connected load. The transmission line has an impedance of 0.06+j0.12 ohms per phase, and the load has an impedance of 12+j9 ohms per phase. For this simple system, find the power factor of the system. (BEP 2015)arrow_forwardQuestion S Analyze the following sequential circuit by a) Write down the state equations b) Write down the outpat equations c) Write down the state table for the sequential circuit 4) Draw the state diagram for the sequential circuit &&& Clock Reset. CROarrow_forward
- Q5arrow_forwardWrite abstract & Itroduction for simple motion detector using 9v battery 555 timer sensor and alarm Abstarct What the project is? How we Built The circuit? How The circuit Can Be Built In Other ways Introduction- What is Motion Detectior What We tried to accomplish with that projectarrow_forwardHello Sir,Good Morning I have a question in my home work related mechatronics lesson. The following below is my question. Please advise thank you.arrow_forward
- Introductory Circuit Analysis (13th Edition)Electrical EngineeringISBN:9780133923605Author:Robert L. BoylestadPublisher:PEARSONDelmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage LearningProgrammable Logic ControllersElectrical EngineeringISBN:9780073373843Author:Frank D. PetruzellaPublisher:McGraw-Hill Education
- Fundamentals of Electric CircuitsElectrical EngineeringISBN:9780078028229Author:Charles K Alexander, Matthew SadikuPublisher:McGraw-Hill EducationElectric Circuits. (11th Edition)Electrical EngineeringISBN:9780134746968Author:James W. Nilsson, Susan RiedelPublisher:PEARSONEngineering ElectromagneticsElectrical EngineeringISBN:9780078028151Author:Hayt, William H. (william Hart), Jr, BUCK, John A.Publisher:Mcgraw-hill Education,