A wood beam carries the loading shown in the figure. calculate the maximum bending stress (in Pa) if P = 4832 N, W = 1517 N/m, a = 1.02 m, b = 2.02 m, c = 1.2 m, L = 86 mm and h = 287 mm. Round off the final answer to two decimal places. A a 88 W b P -c→ 커다 I h

A wood beam carries the loading shown in the figure. calculate the maximum bending stress (in Pa) if P = 4832 N, W = 1517 N/m, a = 1.02 m, b = 2.02 m, c = 1.2 m, L = 86 mm and h = 287 mm. Round off the final answer to two decimal places. A a 88 W b P -c→ 커다 I h

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The timber member has a cross-sectional area of 1653 mm2 and its modulus of elasticity is 12.9 GPa.…

A: Calculate the axial force in each of the segments of the given bar. Then using the algebraic sum of…

Q: For the following composite beam which is built up out of two wooden beams and three steel plates,…

A: Given- For Wood- E = 15 GPa σmax = 7.5 MPa For Steel- E = 200 GPa σmax = 150 MPa To Find- Moment…

Q: The timber member has a cross-sectional area of 1653 mm2 and its modulus of elasticity is 12.9 GPa.…

Q: The properties of the reinforced concrete beam are b = 314 mm, d = 467 mm, Ast = 1047 mm2, and Est /…

A: Given data b = 314 mm d = 467 mm Ast = 1047 mm2 fc = 17.9 MPa fs = 103.2 MPa n = 9 Using…

Q: Which among the formulas below can be used to compute the combined stress at the bottom fiber of a…

A: ASKED: To compute the formula for combined stress at the bottom fiber of a beam subjected to axial…

Q: answer b only

Q: 4-ø28 mm at the bottom and 2-ø20 mm at the top of the beam, Concrete covering to centroid of…

Q: Y ▼ Part A Locate the centroid y of the composite area. Set a = 130 mm, b = 440 mm, d= 30 mm, h=250…

A: Determine a. Centroid of shaded area. b. Moment of inertia about the x'-axis.

Q: 150 mm F = 30N 150 mm water 3m When a 30N force is placed on the end of a floating 150mm x 150mm x…

Q: In (Figure 1), u 4 kN/m and wp7 kN/m. Replace the distributed loading by an equivalent resultant…

Q: Assume that all members are pin connected and P = 5 kN. (Eigure 1) Figure 3 m3 m3 m+ 2007 P P…

Q: Identical steel bars are used to support a 7400-N load as shown. For the properties of steel bar: A…

Q: 2. A wood beam carries the loading shown in the figure. Determine the smallest allowable width b of…

A: Given working stress in bending is 10MPa

Q: thick. It supports an axial load of 1,000 kN. E for timber is 10 GPa and for steel, E = 200G 10 200…

A: Because of strain compatibility δsteel =δtimber σsteel LEsteel =σtimber LEtimber…

Q: A rectangular steel block is 4 inches long in the x direction, 2.5 inches long in the y direction,…

A: Given:- Dimensions of rectangular steel block are Length in x-direction = 4 inches Length in…

Q: Ql: A simply supported reinforced concrete beam has a cross-section as shown in the Figure 1. Using…

A: Solution Given That f'c=21 MPafy= 420 MPa

Q: A rectangular steel block is 4 inches long in the x direction, 2 inches long in the y direction, and…

Q: • width of beam, b = 350 mm • thickness of beam, t = 450 mm • f'c = 20.7 MPa • fy = 415 MPa • steel…

A: Answer We need to find the ultimate moment on the beam. Ultimate Moment(Mu) will be equal to maximum…

Q: 2. Obtain the interaction diagram for the column section whose dimensions and reinforcement are…

Q: Problem #2: P 2 m W = X N |-1m--| -1m- Hs = 0,3 3. Determine the normal force between the crate and…

Q: The properties of the reinforced concrete beam are b = 304 mm, d = 474 mm, Ast = 1139 mm2, and Est /…

Q: A wood beam carries the loading shown in the figure. Determine the smallest allowable width b of the…

Q: A rectangular beam A = 1,520 mm² fu= 27 MPa (cylinder strength) f₁ = 3.5 MPa (modulus of rupture)…

A: As = 1520mm2 fcu = 27MPa (cylinder strength) fy = 400MPa fr = 3.5MPa (modulus of rupture)…

Q: Q3 - For the given wooden beam and cross section, a) Determine the maximum magnitude of P (P>0) by…

A: To determine: a) The value of maximum magnitude of P. b) The value of maximum spacing of nails.…

Q: A high-strength steel band saw, 26 mm wide, runs over pulleys 1200 mm in diameter. What minimum…

Q: Given the beam section, NA and I, determine the following: Maximum Tensile Stress, STmax= MPa (one…

A: Given cantilever beam with uniformly distributing load and it is required to determine the maximum…

Q: Q4: A rectangular beam has the dimensions shown in figure below. Tensile strength in bending…

A: Given: Modulus of rupture, fcr = 3.5 MPa M = 63 kNm fc = 25 MPa fy = 414 MPa Es = 200000 MPa Ec =…

Q: For the beam section shown in figure, determine the centroid (Neutral Axis) and the moment of…

A: A beam is a horizontal part used in building construction that spans an opening and supports a…

Q: Problem 6.108 The wood used for the T-beam has an allowable tensile and compressive stress of…

A: Given :

Q: Two aluminum posts are located at equal distance from the middle steel post as shown. Take note that…

Q: 1. Copper bar shown calculate the stresses when the temperature drop from 85 °C to 50 °C. a =…

A: *Multiple questions* As per our guidelines we are supposed to answer?️ only one question. Kindly…

Q: Homework 3: Q1/ The beam shown in figure below consists from steel and aluminum, find the maximum…

A: Trusses are the most useful structure to carry the different types of load conditions under pressure…

Q: A piece of wood with a triangular cross section contains a rubberized joint to a angle θ with the…

Q: A wood beam carries the loading shown in the figure, calculat mm from the top of the of the beam on…

Q: Problem 4 Find the maximum allowable value of P for the column. The cross-sectional areas and…

Q: Problem #3: P 1 m W = X N E1 m|4s = 0.4 5. Determine the normal force between the crate and the…

Q: 1. Compute the force in each member of the Warren truss shown in Fig 1000 Ib 3000 Ib MATHalino.com…

A: Compute the force in each member of the Warren truss shown in Fig.

Q: Consider the Fink truss shown in (Eigure 1). Suppose that Fi=600 lb and Fy=900 lb. Figure 1 of 1 60…

Q: rectangular steel block is 4 inches long in the x direction, 2 inches long in the y direction, and 3…

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

A: Given data, BC=CD Angle at A- 40 degree

Q: 780 MPa; v = 0.46] rod has a diameter of 90 mm before lo d must not exceed 92 mm when loaded. What…

A: Given data - Young's modulus (E) = 780Mpa Poisson's ratio (v) = 0.46 Diameter of rod (d) = 90 mm…

Q: From the figure shown, fc’ = 18 MPa, fs = 128 MPa, and n = 10. Determine the moment…

Q: The steel channel is used to reinforce the wood beam. Determine the maximum stress in the steel and…

Q: L L T The wooden bar consists of two segments, each of length L. One segment has a square cross…

Concept explainers

Sizing Joists and Rafters

In civil engineering and building construction, joists and rafters are the major components including beams and columns. Almost every structural construction including buildings, skyscrapers, bridges, commercial complexes, and so on makes use of joists and rafters to provide structural integrity to the building. Joists are primarily thick long pieces of metals, concrete, or wood that are used to support the floor and ceiling. On the other hand, rafters form the major component of pitched roofs, which are a series of sloped long pieces extending from a ridged area that makes contact with the plane area of the wall. They account for the load-bearing of the building along with the beams.

Question

A wood beam carries the loading shown in the figure. calculate the maximum bending stress (in Pa) if P = 4832 N, W = 1517 N/m, a
= 1.02 m, b = 2.02 m, c = 1.2 m, L = 86 mm and h = 287 mm. Round off the final answer to two decimal places.
W
P
커다
A
B
t
b
-c→
C
Į
h

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Problem 6: The compound bar containing steel, bronze, and aluminum segments carries the axia! loads shown in the figure. The properties of the segments and the working stresses are listed in the table. Steel 2 ft Bronze 4 ft A (in.²) E (psi) o, (psi) Aluminum 3 ft 2P Steel 0.75 30 × 106 20 000 Bronze 1.00 12 x 106 18 000 4P Aluminum 0.50 10 x 106 12 000 Determine the maximum allowable value of P if the change in length of the entire bar is limited to 0.08 in. and the working stresses are not to be exceeded.
#2 will upvote anyone who will answer correctly. Thanks
Beam ABCD carries a concentrated load and uniformly distributed load as shown below. Draw the shear and moment diagram of the given beam. Show your solution.
Given that the Gerber beam is drawn. Calculate and draw SFD,BMD,NFD Note : 1 ton = 1000kg Solve max in 25-30 mintes thank u
A reinforced concrete beam is shown in the figure below. 0.75-in, diameter rods Wo 20 in. 2.5 in. 8 ft- 8 ft 10 in. Part A Determine the maximum uniform distributed load wn that can be supported by the reinforced concrete beam if the allowable tensile stress for the steel is (Ost )allow = 30 ksi and the allowable compressive stress for the concrete is (oconc )allow = 3 ksi . Assume the concrete cannot support a tensile stress. Take Est = 29(10) ksi , Econe = 3.6(103) ksi Express your answer to three significant figures.
Note: Read the question carefully and give me both right solutions with clear calculations. Don't copy from already available solutions.
I need a quick solution within 15 minutes With put a happy emoji at the end my best wishes Hamoudi
Calculate the design moment strength of a reinforced concrete beam 200 mm x 460 mm if at failure the concrete compression strain is 0.003 and the tensile steel strain is 0.005. The flexure bars are 16 mm in diameter enclosed by 10 mm stirrups. Use f'c = 22 MPa and fy = 420 MPa. Express your answer as a whole number in the unit of kN.m.
Use 3 decimal places. Assume that steel yields.
For the given cross section below, Compute tne meximum stress of concrete and steel. All aimensions are in 'mm'. Use M-150KN-m ana n=8. Tne answers are | MPa ana MPa. 500 200 100 400 3-32mm Ø 100 100 10) 100
A rectangular concrete beam measures 300 mm wide and has an effective depth of 450 mm. Compression steel consisting of two No.22 bars is located 60 mm from the compression face of the beam. If f= 35 MPa and fy = 420 MPa, what is the design moment capacity of the beam for the tensile steel area As = four No. 36 bars in two layers? Provide material properties for concrete and reinforcing steel used in your design.
The answer is close to 60 Ksi. I need help showing the work to get the answer . Please include units. Thanks