a) What type of concrete floor framing is this?b) In this framing system, identify the hierarchy (or order) of which members support other members. In the following table,put a mark (or leave a blank space) to indicate which is the support member for the loads from members along each row.Loads from these membersSlabBeamGirdercolumnc) Calculate the total weight of a 4.5" thick normal weight concrete slab (150 pcf)d) What is the (typical) tributary width of Beams B-2?Are supported by which of the following member(s)?Slab Beam Girder Column22"e) Calculate the average weight of B-2 concrete beams (14" wide by 22" deep), placed at 7-ft on-center spacingT14" 5.6 A partial framing plan and sections for a light-use manufacturing building is shown below. Note the slab type(S-1/S-2),beam type (B-1/B-2) and girder type (G-1/G-2) are denoting on this plan.22'-0"-0-80-20-2G-321'-0"+7-07-0-7'-0"G-462"PARTIAL SECOND FLOOR FRAMING PLAN23-0"24'-0"8-3S-18-1S-28-1S-2B-1S-28-1S-28-1S-28-1All main steel 2" clearEXTERIOR GIRDER-6-8"All main steel 2" clearEXTERIOR BEAMSColumn6-3"-8'-0"8-4S-18-2S-28-2S-28-2S-28-2S-28-2S-28-2INTERIOR GIRDER-7'-0"--G-1(13)+4-4-4-8 INTERIORBEAMS23'-0"-8-4S-18-2S-2B-2S-28-2S-28-2S-2B-2S-28-2

A floor framing plan is given we need to answer the following questions.Note: As per Bartleby's…

a) What type of concrete floor framing is this? b) In this framing system, identify the hierarchy (or order) of which members support other members. In the following table, put a mark (or leave a blank space) to indicate which is the support member for the loads from members along each row. T Loads from these members Slab Beam Girder column Are supported by which of the following member(s)? Slab Beam Girder Column c) Calculate the total weight of a 4.5" thick normal weight concrete slab (150 pcf)

a) What type of concrete floor framing is this? b) In this framing system, identify the hierarchy (or order) of which members support other members. In the following table, put a mark (or leave a blank space) to indicate which is the support member for the loads from members along each row. T Loads from these members Slab Beam Girder column Are supported by which of the following member(s)? Slab Beam Girder Column c) Calculate the total weight of a 4.5" thick normal weight concrete slab (150 pcf)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Give a short description of the space truss and of the suspension bridge
The interior of the big box store is framed with open web steel joists and joist girders supported on HSS (square tube) columns. A partial framing plan showing 4 bays in the building corner is shown below. (The building is 10 bays across and 8 bays deep). The columns are 24’-0” tall. The HSS 8x8x3/8 weigh 37.6 plf, the 24K10 weigh 13.1 plf, and the 36G9N10K weigh 57.0 plf. The roofing consists of open, 1-1/2” deep, Type B, galvanized, 22 gauge, acoustical perforated steel decking with fiberglass insulation that weighs 1.78 psf. (See attachment 1) Determine the total quantity of steel in the building, in tons. Determine the national average bare cost for the columns using section 05 12 23 of RSMeans Determine the national average bare cost for the joists using section 05 21 19 of RSMeans Determine the national average bare cost for the joist girders using section 05 21 23 of RSMeans. Determine the national average bare cost for the steel roof decking using section 05 31 23 of…
1. (a) Calculate the tributary area, AT, for column 2A in the 4th floor (i.e. the column supporting the roof) to be used in calculation of total roof live load on column 1A (note that "roof live load" is different than "floor live load"). (b) Calculate the tributary area, AT, for column 1A in the 2nd floor to be used for calculation of floor live load acting on the column. c) Calculate the tributary area, AT, for column 1B in the 1st floor to be used for calculation of floor live load acting on the column. (d) Calculate the influence area, AI, for column 1B in the 1st floor for floor live load. e) For a specified live load of p. = 40 psf, calculate the design floor live load, pz [psf], for column IB in the Ist floor using floor live load reduction from code (if allowed). () Using your answers from (c) through (e), calculate the axial force, P. [kip], acting at the top of column 1B in the Ist floor due to floor live load. (g) If columns are 16 in. x 16 in. in x-sect, typical floor beams…
Determine the volume of concrete of Girder G3 from gridline A/3-4 if there are 18 identical spans in the plan. Consider the following plan and schedule. PLAN 4 5 3200 7400 6850 5750 (图) {( 1面(8 62 A IC-1 C-3. S2 S5 S5 S2 S2 S6 S6 *measurement is from center to center of the support SCHEDULE OF BEAMS AND COLUMNS BEAM MARK B (mm) H (mm) G2 500 750 G3 500 650 Column Dimension (mm) C-1 600 x 600 C-2 750 x 750 C-3 900 x 900
The floor system used in a school classroom consists of a 4 in. Reinforced stone concrete slab. Sketch the loading that acts along joints BF and side girder ABCD.
Analyze the truss below
1. A 20m Fink Truss are spaced at ‘S’ meters o.c. the purlins are made up of C10X20 sections and are spaced 1.1967m on centers. The truss has a height of 4m. Roof LL is ‘RLL’ N/m2 of roof surface and roof covering is assumed to be ‘RDL’ N/m2 of roof surface. Determine whether the purlins are adequate to carry such loadings. Fy = 248 MPa. C10X20 properties: w=29.76kg/m, A=3787.09mm2, Ix=32.84x106mm4, Iy=1.17x106mm4, Zx=317.91x103mm3, Sx=258.92x103mm3, Zy=44.25x103mm3, Sy=21.47x103mm3 S (m) RLL (N/m^2) RDL (N/m^2) 6.00 900 900 a. Considering sag rods and tie rods at midspan, what is the maximum moment about major axis in N-m? (2 decimal places) b. Considering sag rods and tie rods at midspan, what is the maximum moment about minor axis in N-m? (2 decimal places) c. Considering sag rods and tie rods at midspan, what is the interaction value for combined moment? (2 decimal places)
1. A 20m Fink Truss are spaced at ‘S’ meters o.c. the purlins are made up of C10X20 sections and are spaced 1.1967m on centers. The truss has a height of 4m. Roof LL is ‘RLL’ N/m2 of roof surface and roof covering is assumed to be ‘RDL’ N/m2 of roof surface. Determine whether the purlins are adequate to carry such loadings. Fy = 248 MPa. C10X20 properties: w=29.76kg/m, A=3787.09mm2, Ix=32.84x106mm4, Iy=1.17x106mm4, Zx=317.91x103mm3, Sx=258.92x103mm3, Zy=44.25x103mm3, Sy=21.47x103mm3 S (m) RLL (N/m^2) RDL (N/m^2) 6.00 900 900 a. Considering sag rods and tie rods at midspan, what is the maximum moment about major axis in N-m? (2 decimal places)
3. A 20m Fink Truss are spaced at ‘S’ meters o.c. the purlins are made up of C10X20 sections and are spaced 1.1967m on centers. The truss has a height of 4m. Roof LL is ‘RLL’ N/m2 of roof surface and roof covering is assumed to be ‘RDL’ N/m2 of roof surface. Determine whether the purlins are adequate to carry such loadings. Fy = 248 MPa. C10X20 properties: w=29.76kg/m, A=3787.09mm2, Ix=32.84x106mm4, Iy=1.17x106mm4, Zx=317.91x103mm3, Sx=258.92x103mm3, Zy=44.25x103mm3, Sy=21.47x103mm3 S (m) RLL (N/m^2) RDL (N/m^2) 6.00 900 900 g. Considering sag rods and tie rods at third points, what is the required diameter of sag rods? (rounded value)
3. A 20m Fink Truss are spaced at ‘S’ meters o.c. the purlins are made up of C10X20 sections and are spaced 1.1967m on centers. The truss has a height of 4m. Roof LL is ‘RLL’ N/m2 of roof surface and roof covering is assumed to be ‘RDL’ N/m2 of roof surface. Determine whether the purlins are adequate to carry such loadings. Fy = 248 MPa. C10X20 properties: w=29.76kg/m, A=3787.09mm2, Ix=32.84x106mm4, Iy=1.17x106mm4, Zx=317.91x103mm3, Sx=258.92x103mm3, Zy=44.25x103mm3, Sy=21.47x103mm3 S (m) RLL (N/m^2) RDL (N/m^2) 6.00 900 900 f. Considering sag rods and tie rods at third points, what is the interaction value for combined moment? (2 decimal places)
2. A 20m Fink Truss are spaced at ‘S’ meters o.c. the purlins are made up of C10X20 sections and are spaced 1.1967m on centers. The truss has a height of 4m. Roof LL is ‘RLL’ N/m2 of roof surface and roof covering is assumed to be ‘RDL’ N/m2 of roof surface. Determine whether the purlins are adequate to carry such loadings. Fy = 248 MPa. C10X20 properties: w=29.76kg/m, A=3787.09mm2, Ix=32.84x106mm4, Iy=1.17x106mm4, Zx=317.91x103mm3, Sx=258.92x103mm3, Zy=44.25x103mm3, Sy=21.47x103mm3 S (m) RLL (N/m^2) RDL (N/m^2) 6.00 900 900 e. Considering sag rods and tie rods at third points, what is the maximum moment about minor axis in N-m? (2 decimal places)
For the truss given below, what is the restraint that can not be remove to arrive with a primary structure?