solve using bernoulii formula and show cancelation of proportionality constant pls A water stream at pipe AB divides into two branches as shown in the figurebelow. The average velocities and areas are shown in the figure. Find thevelocity in one of the branches illustrated as VEL @ pt. DC DIA. = 1 inchVEL. = 2.2 m/sAВDIA. = 2 inchesDVEL. = 2 m/sDIA. = 2 inchVEL. =

given data; ⇒diameter of pipe A (dA)=2inch=0.0508m⇒velocity in pipe (VA)=2m/s⇒diameter of pipe C…

Answered: A water stream at pipe AB divides into…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

63. Water is flowing out of a small hole located at a depth of h below the freesurface of a large reservior. Find the equation of the stream leaving the hole in thecoordinate shown in the figure. [Ans.: y = x2/4h].
P1 = Patm 1 V 7.3 m/s %3D Flow h = 0.96 ft water 3 Density of water 1000 kg/m Determine the pressure at the point 3?
Q1) Using a system similar to that shown in figure, if air pressure p = 50 kPa., and the depth h1 = 0.3 m, compute the water flow from side nozzle of diameter (d = 10 mm) and the rise h₂ from that nozzle. vesn Air pressure It, 11₂ Nozzle
What is the velocity of the pipe center (m/s)? Given that h3=31.3 cm hy =7 cm 3D3 cm] Water.
pls replyy asap A pipe that is 200 mm in diameter (point 1) diverges into segments 150 mm (point 2) and 90 mm (point 3) diameter respectively. If Q1 = 50 lit/s and v2 a 1.2 m/s, find the velocity at point 3.
Q1: Water is flowing from tank A to tank B as shown in the following figure. The flow is steady so that the water level in tank B does not change. Find h, in the figure. The density is constant. The flow is inviscid and irrotational. Hint: apply Bernoulli's equation between the free surface and the discharge for tanks A and B individually. Then, since the flow rate leaving tank A (and entering tank B) must equal the rate leaving tank B, these two Bernoulli's Equations can be substituted and solved for one unknown. 1 10.0 cm = 0.01 m Tank A 士 Tank B d 0.02 m Figure 1. Q1
a pump is delivering 160 liters per sec of water using an impeller diameter of 240 mm and operating at a speed of 1800 rpm. if the speed held constant and the impeller diameter is change to 203.2 mm, what is the new dischange og the pump in liters per second
P = Patm 1 Vį = 6.9 m/s Flow h = 0.89 ft water 2 Density of water = 1000 kg/m³ Determine the pressure at the point 3?
SUPPLEMENTARY QUESTION The figure shows two reservoirs connected by a pipe. The discharge rate in the pipe is known to be equal to SN/100 (m2/s) (where SN is the sum of your student number). Calculate the height of the second reservoir (H2), and the pressure head, velocity head and elevation head at point 3 (mid-point of the pipe). HI 300 m H2 datum A = SN/1000 L = 100 x SN (m) D 0.3 m Please solve these question my sn number 31
3. The below figure shows a pipe with a circular cross section of diameter D mm on the left end and a square cross section with side D mm on the right end. Mercury enters the left end with a velocity 1 cm/s and leaves the right end with a velocity V2. Find V2 (neglect losses in the pipe). Inlet Outlet Cannot be find since length is not given Cannot be find since diameter is not given а. b. 7.85 mm/s 12.73 mm/s с. d.
1.Find the diameter of a pipe of length 3000 m when the rate of flow of water through the pipe is 300 litres/s and the head lost due to friction is 5 m. Take the value of C = 50 in Chezy’s formula.
a) Two pipes have a length ? each. One of them has a diameter D, and the other a diameter d.if the pipes are arranged in parallel, the loss of head when a total quantity of water Q flows through them is h, but, if the pipes are arranged in series and the same quantity Q flows through them, the loss of head is H. If ?=?/2, find the ratio of H to h, neglecting secondary losses and assuming the pipe coefficient f has a constant value. b) A pipeline of 0.6m diameter is 1.5km long.To increase the discharge, another line of the same diameter is introduced parallel to the first in the second half of the length.Neglecting minor losses, find the increase in discharge if 4f = 0.04. The head at inlet is 300mm. c) Determine the difference in the elevations between the water surfaces in the two tanks which are connected by a horizontal pipe of diameter 300 mm and a length of 400 mm. The rate of flow of water through the pipe is 300 litres/s. Consider all losses and takef=0.008. d) Water at 20°C is…

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

A water stream at pipe AB divides into two branches as shown in the figure below. The average velocities and areas are shown in the figure. Find the velocity in one of the branches illustrated as VEL @ pt. D C DIA. = 1 inch VEL. = 2.2 m/s A DIA. = 2 inches VEL. = 2 m/s D DIA. = 2 inch VEL. = B