A water drain pump can be activated depending on the status of three switches, one main switch and two secondary switches. The pump is activated if and only if the main switch is turned ON and one of the secondary switch is turned ON. a. Find the minterm expansion in Σ – form. b. Find the maxterm expansion in Π – form. c. Find the minimum SOP expression. d. Find the minimum POS expression. e. Create a logic circuit diagram using the minimum number of gates used.

A water drain pump can be activated depending on the status of three switches, one main switch and two secondary switches. The pump is activated if and only if the main switch is turned ON and one of the secondary switch is turned ON. a. Find the minterm expansion in Σ – form. b. Find the maxterm expansion in Π – form. c. Find the minimum SOP expression. d. Find the minimum POS expression. e. Create a logic circuit diagram using the minimum number of gates used.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Design a logic circuit with four inputs and one output that will produce "l" in the output only if the input patterns have odd number of zeros. a) Write the Boolean equation for the circuit in the simplest SOP form. b) Draw the logic circuit for the above equation in its simplest form. c) Re Design the logic circuit using NANI) gates only?
Palagiaph 1. Find logic finctions for the circuits shown below. F
Write a VHDL code for the following simple logic circuit. D- X1 X2 f X3
DIGITAL LOGIC DESIGN Are the following addition results Overflow or underflow and why?
A synchronous logic circuit has one JK and one D flip-flop. There is no output in the circuit. The entry is represented by an X. Y is the output of JK flip-flob, and Yo is the output of D flip-flobe. Logic functions of the inputs of flip-flops are given below. J = XY. K = X, D = XY, A Draw the state diagram of the synchronous circuit. Note: Take the states (Y, Yo) in 2 order.
8688388台 825 Quiz 13-1-2022 entals of Logic Circuits( X 1FAlpQLSdMDtMq7nUPYhVea-B3aXsGRjrUDgfSOq91R3h2eTqLypfdkg/formResponse According to the circuit in below, find-out the function describes correctly * the circuit output (F) B. 2. 60 DI2 O D. (F)is non of these functions () F3D(A xnorC) 71°F Cloudy 7 ES 近。
Design circuit that has an input w and an output z. The circuit is a sequence detector that produces z = 1 when the previous two values of w were 00 or 11; otherwise z = 0. Use W=0101100010101110101011100010 a) For this problem design the circuit using JK flipflops, draw the state diagram, true table, logic circuit.
Design the following combinational logic circuit with a four-bit input and a three-bit output. The input represents two unsigned 2-bit numbers: A1 A0 and B1 B0. The output C2 C1.C0 is the result of the integer binary division A1 A0/B1 B0 rounded down to three bits. The 3-bit output has a 2-bit unsigned whole part C2 C1 and a fraction part CO. The weight of the fraction bit CO is 21. Note the quotient should be rounded down, i.e. the division 01/11 should give the outputs 00.0 (1/3 rounded down to 0) not 00.1 (1/3 rounded up to 0.5). A result of infinity should be represented as 11.1. A minimal logic implementation is not required. (Hint: start by producing a truth table of your design).
Consider the circuit below. The switches are controlled by logic variables such that, if A is high, switch A is closed, and if A is low, switch A is open. Conversely, if B is high, the switch labeled is open, and if B is low, the switch labeled is closed. The output variable is high if the output voltage is 5V, and the output variable is low if the output voltage is zero. a. Write a logic expression for the output variable. b. Construct the truth table for the circuit. A Logic 1 5V(+ B C Logic 0 R
mybmsajmanac ERSITY Design My courses Logic Design General Qua 2 LD/DLD on Tue. 7/12/21-Dr. Zidan The correct state sequence of the cirtut with initial state Qo1, 01 and Q0 D. Q D, a. LSB MSB Clock Select one O a1, 2, 5.3, 7,6,4 O b.1,6, 5,7, 2.3,4 O C1,2.7,3, 5,6, 4 O d 1,3,4, 6, 7,3.2
Design a logic circuit for decoder that accepts 3-bit input and displays alphabet “048” at the seven- segment as illustrated at Figure 1 (a). The input-output mapping shown in Table 1 (a). Refer Figure 1(b) and Figure 1(c) for seven-segment display format showing arrangements of segments using common anode connection. Show each steps clearly to produce the expressions and required design. [Rekabentuk litar logik untuk penyahkod yang menerima input 3-bit dan paparkan abjad "048" di tujuh-segmen seperti digambarkan pada Rajah 1(a). Pemetaan masukan-keluaran ditunjukkan dalam Jadual 1(a). Rujuk Rajah 1(b) and Rajah 1(c) untuk format paparan tujuh-segmen yang menunjukkan susunan segmen menngunakan sambungan 'common anode'. Tunjukkan setiap langkah dengan jelas untuk menghasilkan ungkapan dan reka bentuk yang dikehendaki.] Xs X6 X7 DECODER Figure 1(a) [Rajah 1(a)] a b с d e f g a 80123456789 Figure 1(c) [Rajah 1(c)] g Figure 1 (b) [Rajah 1(b)] b с DP
Logic Design courses / EE200SP21 / General / Mid Term Examination Part II (Subjecti Compute the minimal products of sum and minimal sum of products expressions for following KMAP. Show your groupings on KMAP АВ CD 1 1 1 1 0. Instructions: You have to solve the answer by hand on paper, scan/take photo and upload it as a single file. Local Disk (D:) Mid Term Examinat.