A) Water at 70 °C flows up a 50-ft-long conical pipe with its centerline sloping at 5° to the horizontal, as shown in figure (1). At its lower end the diameter is 24 in, the water pressure is 15 psi; at its upper; outlet end the diameter is 18 in and the water pressure is 12.5 psi. By a method, the shear stress found to be 0.25 lb/ft². Assuming this value to be non-varying, calculate the flow rate. given = 62.30 lb/ft³. 10 in die fo fr 24 in de 15 pi 32-0.25 46/4 Figure (1) 12.6 pri

A) Water at 70 °C flows up a 50-ft-long conical pipe with its centerline sloping at 5° to the horizontal, as shown in figure (1). At its lower end the diameter is 24 in, the water pressure is 15 psi; at its upper; outlet end the diameter is 18 in and the water pressure is 12.5 psi. By a method, the shear stress found to be 0.25 lb/ft². Assuming this value to be non-varying, calculate the flow rate. given = 62.30 lb/ft³. 10 in die fo fr 24 in de 15 pi 32-0.25 46/4 Figure (1) 12.6 pri

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2) For the same system of question 1, let Az = 80 m and L pipe diameter for which the flow rate will be 7 m³/h? = 185 m of cast-iron pipe. What is the
The Young's modulus of a material is 125 GPa and Poisson's ratio is 0.25. The modulus of rigidity of the material is
Question 3 Water (p = 1000 kg/m³, μ = 1.12 x 10-3 Ns/ m²) flows through a 0.01-m-diameter pipe at a velocity of 2 m/s. The length of the pipe is 40 m. A pump is used to maintain the flow from one reservoir to another reservoir as shown. The following data are available: KL elbow = 1.5, Kentrance = 0.5, Kexit = 1.0. Elbow Pump Elbow Figure Q1 Note that the entrance and exit are at the same elevation. The free surfaces of the reservoirs are also at the same elevation. (a) Calculate the total head losses in the pipe.
The water is delivered with piping system given in the figure below. The levation difference between entering section and tank is 143,55 m. Estimate the gage pressure [MPa] at point 1. (Note: For water at 20°C, take p=998 kg/m and u=0.001 kg/ms. ) 5 cm diameter cast-iron pipe Length of the system is 1.2 km All fittings are flanged. The vohume flow rate is 300 L min 45 treaded elbow Yanit
The square-section duct in atmospheric conditions is exposed to outside air flow as seen in the figure. The temperature of the air is T air= 5°C, the velocity is V air= 10m/s. Find the exit temperature of the water entering the channel at a flow rate of ṁwater=0.01 kg/s and a temperature of T water,g=50°C. Geometric dimensions are given on the figure.
Air (diatomic, MW = 28.8664 g/mol) at 1.7 atm gage (where Pam = 1 atm) and 15°C enters a 70-m long horizontal 75-mm-ID steel pipe (€ = 4.6(10) m). The velocity at the entrance of the pipe is 60 m/s. Assuming isothermal flow, what is the absolute pressure (atm) at the discharge end of the line? Use Churchill equation for the friction factor.
PLease answer this correctly ASAP. Note:Tolereance is ± 1 in the 3rd significant digit. Exact answer please. This is a step by step question and I font have enough time to answer this so please can you answer all the necessary information/joints/points? I will rate you based on your answer. Thank you so much
In a fully developed turbulent flow through a pipe, the shear stress is……… Please fill the blank correctly.
The pressure drop in a horizontal commercial steel pipe should not exceed 1 psi per 150 feet of pipe length for flow rates up to 500 gal/min. If the water temperature is never below 50 F°, determine the necessary pipe diameter.
Water at 15°C is flowing in a 3 inch horizontal Schedule 40 steel pipe at a pressure of 102 kPa. The pipe reduces to a 1.5 inch Schedule 40 steel pipe. What is the flow rate if pressure in the 1.5 inch pipe is 99.8 kPa?
A saturated steam at 410K is being transported in a pipeline (brass drawing tubing) at a rate of 1 grams/second. Pipe has inside diameter of 0.025 m . The tube is 100m long. The pressure at the entrance is 80kPa. What is the value of G in kg/s.m2?. (use Perry's Handbook for the properties and constants) R = 8314J/kgmol.K; MW=18.02g/mol
The smooth pipes used in the pumping system in the figure below have a diameter of 150 mm. and its total length is 80 m. In this system; There are four bends with a loss coefficient of 0.2. Lost coefficients; 0.5 for the inlet to the pipe, 0.7 for the valve and 1 for the entrance to the tank. z2-z1 = 15 m above If the flow rate of the water pumped to the tank is 50 L / s and the overall efficiency of the pump is 84%, the manometric discharge Find its height and strength. Take the viscosity of water as 0.001 kg / m.s.