A voltage waveform is given in volts as: v(t) = 0.06 sin (6500t-61⁰) 1. Calculate the RMS value of this voltage waveform. 2. Determine the dc value of its half-rectified form. 3. Express this voltage as a phasor in polar form. 4. Determine the frequency AND the time period of this voltage waveform. 5. Sketch this voltage waveform using degrees as horizontal axis.

A voltage waveform is given in volts as: v(t) = 0.06 sin (6500t-61⁰) 1. Calculate the RMS value of this voltage waveform. 2. Determine the dc value of its half-rectified form. 3. Express this voltage as a phasor in polar form. 4. Determine the frequency AND the time period of this voltage waveform. 5. Sketch this voltage waveform using degrees as horizontal axis.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
7 Find the average and effective values of voltage for sinusoidal waveform shown in Figure. Vm = 100 V 2x x14 9714 [Ans: 27.17 V, 47. 67 V]
(b) An engineer is required to analyse a sinusoidal waveform for the voltage and current using oscilloscope. The voltage waveform produced Root Mean Square (RMS) value at 75 V with positive-going zero crossing at 30°. While the RMS value of current is 66.71 A with negative-going zero crossing at 0.349 rad. Assume the frequeney of both waveforms is 50 Hz. (i) Sketch the voltage and current waveform in the same axis by showing the important point. (ii) Determine instantaneous voltage when t = 8ms . (iii) Determine phase relationship between voltage and current waveform.
2. Refer to the Figure 2. a) Determine the total impedance of the circuit in polar form. b) Determine the voltage v(t) and current i(t) sinusoidal forms. Sketch one cycle of the waveforms in the same x-axis. Clearly indicating the peak value and the period of each waveform and the phase difference (in milliseconds) between the two waveforms. c) Determine the values of resistance R and inductance L. d) Determine the phasors V,, VR and Vc. e) Sketch the phasor diagram showing Vs, Vr, Vr, Vc and I.
Shown in the figure below is an "RC" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 11.58 Volts and is running at a frequency of f = 1.326e+04 Hz. resistor has a resistance of R = 3750 2 and the capacitor has an capacitance of C = 3.17e-09 Farads. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Write the FORMULA for the phase of the total impedance of the circuit tot = Determine the numerical value of Ztot = Determine the numerical value of Pztot= Determine the current through the circuit: • I(PEAK) = • I(RMS) = Determine the voltage across the resistor: Amps Amps S2 C degrees
How do I find the phase of this sinc function?
a) Using your own words, describe how triangular waveforms are produced from sinusoidal waveforms. b) Write a sinusoidal formula that will produce a triangular wavefor y c) Demonstrate your understanding by plotting the formula shown in b using any of the plotting software.
Design a circuit to limit a 20 V rms sinusoidal voltage to a maximum positive amplitude of 10 V and a maximum negative amplitude of using a single 14 V dc voltage source.
1 Calculate average and RMS value of the voltage waveform given in Figure. 4V %3D t(ms)- 4V
1. What effect does changing the frequency on the effective value of sinusoidal voltage? 2. What effect does changing the amplitude on the effective value of sinusoidal voltage?
An alternating current is given by the expression i = 200 sin (314t + T/6) amperes. The maximum value is and the frequency of the current is