A voice-grade telephone line with bandwidth of 4 kHz (0 – 4kHz) is to be used in full-duplex transmission mode to transmit BFSK signals, produced by a modem, with frequency deviation set to 100 Hz and d-0. (i) (ii) (iii) State what is meant by full-duplex transmission modes. Determine the maximum bit rate supported by this scheme. Determine the mark and space frequencies in one direction.

A voice-grade telephone line with bandwidth of 4 kHz (0 – 4kHz) is to be used in full-duplex transmission mode to transmit BFSK signals, produced by a modem, with frequency deviation set to 100 Hz and d-0. (i) (ii) (iii) State what is meant by full-duplex transmission modes. Determine the maximum bit rate supported by this scheme. Determine the mark and space frequencies in one direction.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

(5) If in a communication system BPSK, QPSK, QASK-8 are used for transmission and reception of digital data. (a) Determine the bandwidth B for each modulation scheme for a bit rate of 2kbps (b) Determine the symbol distance for each modulation scheme providing its complex plain presentation in terms of bit energy Es (c) Determine the number of symbol and the symbol rate for each modulation.
1) Compared to AM, frequency modulation (FM) is known for it's: a. efficient bandwidth utilization. b. efficient noise cancellation. c. efficient against channel non-linearity. d. both b and c.
A. If the probability of error of BPSK is 0.85 then Pe of BFSK is? B. What happens to the radio wave propagation when the rouefractive index of ionospheric layer becomes low or high? C. If the number of quantization levels are multiplied by four time them how many numbers of bits are added to the actual number? D. What is the disadvantage of wave tilt? E. What is a bipolar line coding technique with phase encoding, and explain why it is named as phase encoding method? F. What is oblique communication circuit? G. What are the differences between DPCM and Delta Modulation? H. What is the change in bandwidth when channel capacity is doubled and two number of bits are increased?
Explain frequency hopping acquisition scheme using a simple PN sequence. Assume that the length of PN sequence is 15 and the number of frequency hopping levels is 8
If in a communication system BPSK, QPSK, QASK-8 are used for transmission and reception of digital data. (a) Determine the bandwidth B for each modulation scheme for a bit rate of 2kbps (b) Determine the symbol distance for each modulation scheme providing its complex plain presentation in terms of bit energy E (c) Determine the number of symbol and the symbol rate for each modulation.
q6- Consider an Orthogonal frequency-division multiplexing data transmission mode of bandwidth 60 KHz with a cyclic prefix of 33 samples. There are 120 carriers used for data transmission, the outer 30 carriers are used for reducing adjacent channel interference, and 10 carriers are the pilot symbols. Calculate the symbol time for the raw OFDM in (milli second) Select one option: a. 5 b. 3 c. 1 d. 2
Q24)This multiple choice question from DIGITAL COMMUNICATIONS course.just write for me the final answer. The choice of the number of bits per PCM word depends on the a. SNR b. Bandwidth c. None of the mentioned d. SNR and bandwidth
In a baseband communications link, frequencies upto 3500 Hz are used for signalling. Using a raised cosine pulse with 75% excess bandwidth and for no inter-symbol interference, the maximum possible signalling rate in symbols per second is
Please help me with my homework. Thanks! The course subject is Fundamentals of Electronic Communications. 2. A 75 MHz carrier having an amplitude of 50 V is modulated by a 3 KHz audio signal having an amplitude of 20 V. Determine the modulation index, % modulation, fusb, flsb, AM equation.
Consider a telephone line initially noiseless channel having bandwidth and signal level determined by the network engineer. Calculate maximum data rate. After certain distance the channel becomes extremely noisy, so that the noise is strong which faints the signal .Calculate the capacity of the channel.
Why SSB is preferred for transmission of good quality signal
A 450 kHz carrier signal is modulated with a 15 kHz modulating signal. What are its sideband frequencies?