a vertical uniform beam of length Lthat is hinged at its lower end.A horizontal force F is applied to the beam at distance y from the lower end. The beam remainsvertical because of a cable attached at the upper end, at angle uwith the horizontal. gives the tension T in the cableas a function of the position of the applied force given as a fractiony/L of the beam length.The scale of the T axis is set by Ts= 600 N.Figure 12-49c gives the magnitude Fh of the horizontal force on thebeam from the hinge, also as a function of y/L. Evaluate (a) angle uand (b) the magnitude of .

a vertical uniform beam of length Lthat is hinged at its lower end.A horizontal force F is applied to the beam at distance y from the lower end. The beam remainsvertical because of a cable attached at the upper end, at angle uwith the horizontal. gives the tension T in the cableas a function of the position of the applied force given as a fractiony/L of the beam length.The scale of the T axis is set by Ts= 600 N.Figure 12-49c gives the magnitude Fh of the horizontal force on thebeam from the hinge, also as a function of y/L. Evaluate (a) angle uand (b) the magnitude of .

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter10: Rotational Motion

Section: Chapter Questions

Problem 32P

See similar textbooks

Similar questions

A beam with length of 2 m and a mass of 10 kg supports a 50 kg box. The beam is connected to a wall by a hinge at its base and a horizontal wire. The wire is connected to the beam 1.5 m from the hinge and makes an angle θ of 35o to the beam. The goal is to find the tension in the wire and the horizontal and vertical components of the force exerted by the hinge on the board. Suppose the maximum tension that the wire can withstand is 1500 N. What is the maximum load that the hinge can support before the wire breaks?
A beam with a length of 2 m and a mass of 10 kg supports a 50 kg box. The beam is connected to a wall by a hinge at its base and a horizontal wire. The wire is connected to the beam 1.5 m from the hinge and makes an angle θ of 35o to the beam. The goal is to find the tension in the wire and the horizontal and vertical components of the force exerted by the hinge on the board
One end of a uniform rod of weight w = 73.5 N and length L = 2.55 m is supported by a cable at an angle of ? = 37.0°above the rod. The other end rests on a small frictionless support and presses into a wall as shown in the figure. Determine the magnitude n of the vertical normal force exerted by the support on the rod and find the magnitude T of the tension in the cable.
A 1682-N uniform beam is attached to a vertical wall at one end and is supported by a cable at the other end. A 1594-N crate hangs from the far end of the beam. Find the magnitude of the tension in the wire. The angle theta (0) is 26 degrees and the angle phi (0) is 58 degrees. The length of the beam is L. Вeam
A uniform rod has one end attached to a vertical wall by africtionless hinge. A horizontal wire runs from the other end of the rodto a point on the wall above the hinge and holds the rod at an angle θabove the horizontal. You vary the angle u by changing the length ofthe wire, and for each θ you measure the tension T in the wire. You plotyour data in the form of a T-versus-cot u graph. The data lie close to astraight line that has slope 30.0 N. What is the mass of the rod?
A uniform drawbridge must be held at a 38o angle above the horizontal to allow ships to pass underneath. The drawbridge weights 55000 N and is 15.0 m long. A cable is connected 3.5 m from the hinge where the bridge pivots (measured along the bridge) and pulls horizontally on the bridge to hold it in place. What is the tension in the cable? Find the magnitude and direction of the force the hinge exerts on the bridge. If the cable suddenly breaks, what is the magnitude of the angular acceleration of the drawbridge just after the cable breaks? What is the angular speed of the drawbridge as it becomes horizontal? What is the velocity of the drawbridge, just before it “hits” (i.e. goes horizontal)?
A 1323-N uniform beam is attached to a vertical wall at one end and is supported by a cable at the other end. A 1575-N crate hangs from the far end of the beam. Find the magnitude of the tension in the wire. The angle theta () is 25 degrees and the angle phi () is 59 degrees. The length of the beam is L.
As shown below, a sign weighing 430 N is hanging (via a wire) from a uniform 169 N beam of length L. Additionally, the beam is attached to a cable that makes an angle e (0 = 49°) with the beam. 0.9 L Determine the tension in the cable and the magnitude & direction of the force the hinge (the orange circle) exerts on the beam. Cable tension = Hinge force = Direction of hinge force = ° relative to the horizontal in quadrant -- Choose quadrant -- v 0.8L
A uniform ladder 5.0 m long rests against a frictionless, vertical wall with its lower end 3.0 m from the wall. The ladder weighs 160 N. The coefficient of static friction between the foot of the ladder and the ground is 0.40. A man weighing 740 N climbs slowly up the ladder. (a) What is the maximum friction force, in Newtons, that the ground can exert on the ladder at its lower end? (b) What is the actual friction force, in Newtons, when the man has climbed 1.0 m along the ladder? (c) How far, in meters, along the ladder can the man climb before the ladder starts to slip?
The system in the figure is in equilibrium. A concrete block of mass 275 kg hangs from the end of the uniform strut of mass 31.9 kg. For angles o = 20.7° and e = 60.3°, find (a) the tension Tin the cable and the (b) horizontal and (c) vertical components of the force on the strut from the hinge. Strut -I linge
In the figure, a uniform beam with weight W and length is hinged at its lower end, and a horizontal force of magnitude F acts at its upper end. The beam is held vertical by a cable that makes angle with the ground and is attached to the beam at height h. NOTE: Give your answer in terms of the variables given. (a) What is the tension in the cable? T = Fl h cos(0) (b) What is the x-component of the force on the beam from the hinge? FF-Tcos(0) Fu L X (c) What is the y-component of the force on the beam from the hinge? Tsin(0) = h X
One end of a uniform ℓ = 4.70-m-long rod of weight w is supported by a cable at an angle of ? = 37° with the rod. The other end rests against a wall, where it is held by friction (see figure). The coefficient of static friction between the wall and the rod is ?s = 0.520. Determine the minimum distance x from point A at which an additional weight w (the same as the weight of the rod) can be hung without causing the rod to slip at point A.