A vertical shaft DA is attached vertically to a fixed base at A and is subjected to the torques as shown in the attached figure. At Segment AB is a hollow segment, L = 600 mm, inner diameter = 44 mm, at Segment BC, L = 200 mm, diameter = 60 mm, Segment CD is L = 400 mm, diameter = 30 mm. Take G = 77 GPa. There is an applied torque T1 = 3500 N- m at C, and T2 = 250 N-m at D. Determine: a. The shearing stress at Segment AB. b. The shearing stress at Segment BC. c. The summation of angle of twist. Show complete solution with FBD

Q: A solid constant-diameter circular shaft is subjected to the torques of TA = 480 lb-ft, TB = 1060…

A: Given Data: Allowable shear stress, t=5800 psi

Q: An alumium shaft shown in figure-2, has x-sectional area in the shape of equilateral triangle. if…

A: Write down the given values using suitable variables. Here τ signifies allowable shear stress, ϕ…

Q: Q.5. A single torque of T = 50 N.m is applied to a compound torsion member as shown in figure (5).…

A:

Q: (A,) See the figure below. There are two torques applied at B and D. Segment CD is a tube, while AB…

A: In the given problem, the dimensions and Modulus of rigidity have been converted to feet. Radius,…

Q: Q.6. A circular bar AB with ends fixed against rotation has a hole extending for half of its length…

A:

Q: (a) Determine the support reactions for the stepped circular shaft shown below. (b) Plot the…

A: GIVEN :- T1=200lb-inT2=100lb-inT3=500lb-indAB=3 indCE=2 inE=30×106psiμ=0.3SOLUTION :-Torque on…

Q: e composite shaft shown in Figure consists of a solid brass segment one and a solid aluminum segment…

A: Given values in the question:Torque is T=270 N-mIn the Aluminium segment,d2=24 mm; L2=165 mm; G2=28…

Q: 3.4-3) A stepped shaft ABCD consisting of solid eircular segments is subjected to three torques, as…

A:

Q: 3.4-3 A stepped shaft ABCD consisting of solid circular segments is subjected to three torques, as…

A: Given: Torque at D TD=9k.inTorque at C TC=9k.inTorque at B…

Q: 1. See figure below and solve for the maximum value of torque the composite shaft can accommodate…

A:

Q: 3.5-2 The outer diameter of the hollow aluminum shaft (see figure) is d 2 =100 mm^ and the inner…

A:

Q: 400 mm 400 mm 11th. Of the spindle in the figure AB the portion is full and BC part is empty. To the…

A: Given, Total applied Torque (T)= 8kNm Modulus of Rigidity (G)= 80GPA Solution Divide the spindle…

Q: The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter…

A:

Q: 1. See figure below and solve for the maximum value of torque the composite shaft can accommodate…

A: For solution refer below images.

Q: 4 The shaft ABCD shown in Figure Q4 is fixed on both ends. Two (2) external torques are applied at…

A: Answer: (a) The reaction torque at A and D are 485 N•m and 515 N•m respectively. (b) The maximum…

Q: 10 N-m 8 N 45°- D 50° 45°1 F1 A 150 mm xr 30° E

A:

Q: 3.8-4 A hollow steel shaft ACB of outside diameter 50 mm and inside diameter 40 mm is held against…

A:

Q: A hollow aluminum shaft (see figure) has an outside diameter d,- 3.4 in. and inside diameter d, -…

A: Data given-  d2 = 3.4 in  so  r = 1.7 in  d1 = 1.7 in  Angle of twist per unit distance = 0.46°/ft…

Q: The outer diameter of the solid steel pipe shown in the figure is 25 mm. If the pipe is fixed at…

A:

Q: Figure Q1 shows a 1.4 m long steel shaft that consists of a hollow segment AB and a solid segment…

A: From the above figure : TB=TA+750...........................(1)

Q: Figure Q6 shows a circular shaft AB and a square shaft BC where it is fixed at C. а. Determine the…

A:

Q: A steel shaft (Gs = 80 GPa) of total lengthL = 3.0 m is encased for one-third of its length by…

A: Given that, Gs=80 GPa,Length of steel shat, L=3 m,Gb=40 GPa,d1=70 mm,d2=90 mm,…

Q: 10 N-m 8 N 45°- 50° 45°L F1 150 mm 30° E

A:

Q: Note: J3 = J2 G3 = G2 36 mm 0.99x10° mm* (1) 4 kN-m 70 GPa (2) 32 mm (3) 1.65x10 mm“ B 1000 mm C 20…

A:

Q: 3.4-18/ A prismatic bar AB of length L and solid circular cross section (diameter d) is loaded by a…

A: GIVEN DATA - A SHAFT WITH DIA d LOADED UNIFORMLY TORQUE WE HAVE TO FIND BOTH POINT a and b

Q: A solid constant-diameter circular shaft is subjected to torques TA = 420 lb- ft, TB = 1,040 lb- ft,…

A: Right hand rule states that when axis direction is indicated by the thumb, the direction of fingers…

Q: 4 - An aluminum circular shaft, fixed at both ends, is loaded by torques applied at points B and C,…

A:

Q: A solid circular shaft AB of length 504 mm is fixed against rotation at both ends as shown in fig.…

A: Given data: LAB = 504 mm                     dAC = 41 mm                    dCB = 62 mm…

Q: A solid steel shaft ABC with diameter d =40 mm is driven at A by a motor that transmits 75 kW to the…

A:

Q: F2. A circular shaft fabricated from steel is supported at each end by rigid constraints, as shown…

A: Given data: LA=LB=60 in=5 ftT=900 ft.lbdA=2.5 in=0.208 ftdB=2 in=0.1667 ft Need to determine the…

Q: The outer diameter of the solid steel pipe shown in the figure is 25 mm. If the pipe is fixed at…

A: Principle Stresses : planes in which plane shear stress is zero are known as principle plane and…

Q: A stepped shaft ABC consisting of two solid circular segments is subjected to torques '1 and T,…

A:

Q: The solid 25-mm-diameter shaft is used to transmit the torques applied to gears C and D shown in…

A:

Q: Note: J3 = J2 46 mm G3 = G2 4.93×10 mm (1) 16 kN-m 50 GPa (2) 34 mm %3D (3) 2.10x106 mm 900 mm 35…

A:

Q: A 3 m long steel angle shown in the figure has a section thickness of 12.7 mm and a cross sectional…

A:

Q: F3.A shaft is composed of two 6-in. diameter sections coupled together (see figure below). Part AB…

A: Introduction: A composite shaft is formed when two shafts of different materials are joined together…

Q: 3.44. A circular shaft having diameters D and d and a groove of radius r (see Fig. 3.17, with M 0…

A: Given Data The shear stress is: τall=250 MPa The outer diameter is: D=28 mm The inner diameter is:…

Q: 7. A stepped shaft ABC consisting of two solid circular segments is subjected to torques Tị and T;…

A: Data given -  d1 = 58 mm = 0.058 m  L1  = 760 mm = 0.76 m d2  = 45 mm = 0.045 m  L2 = 510 mm = 0.510…

Q: Prob. 4.5-9. Use the following data with Fig. P4.5-9: G = 11 × 10° psi, L1 = 10 in., L2 = 15 in., L3…

A:

Q: n in the figure. Find the angular rotation of D, the right end of one shaft, with ect to A, the left…

A:

Q: 3) Two circular shafts (shown in Figure) made of the same material and have the same length are…

A:

Q: 3.7-4 The drive shaft for a truck (outer diameter 60 mm and inner diameter 40 mm) is running at 2500…

A:

Q: 45 mm B 60 mm 30 mm 2 m -1.2 m

A:

Q: A horizontal compound shaft AC is attached to a fixed wall at the point C and two torques Tand 2T…

A:

Q: A solid brass bar of diameter d =1.25 in. issubjected to torques T1, as shown in part a of the…

A: d=1.25Applied troque on the solid bar be T1Allowable shear stress in the brass τa=12ksiPolar moment…

Q: 3.7-4 d = 40 mm is driven at A by a motor that transmits 75 kW to the shaft at 15 Hz. The gears at B…

A:

Q: 3.3-2 When drilling a hole in a table leg, a furniture maker uses a hand-operated drill (see figure)…

A: Given data Diameter of bit =d=4.0 mm. To determine : (a) If the resisting torque supplied by the…

Q: Ex: A Torque (T) is applied to a solid taper shaft with built-in ends, as shown in Figure, Determine…

A:

Q: Q2 / A solid steel [G= 80 GPa] shaft of variable diameter is subjected to the torques shown in…

A: (a) Draw the diagram for the problem.

Q: The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter…

A:

Q: 3.4-7 A solid steel shaft ABCDE turns freely in bearings at points A and E. The shaft is driven by…

A:

Q: Problem II. The figure below shows the cross-section of a thin-walled shaft subjected to a torque MT…

A: The section is as shown below, Section I: -   Area, A1=π2a2 Section II: - Area, A2=2a×2aA2=4a2…

Q: A stepped shaft ACB having solid circular cross sections with two different diameters is held…

A:

Q: The torsional assembly shown in Figure 1 consists of solid 2.50-in.-diameter aluminum [G = 4,000…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.