A vertical pipe column with an outside diameter of D=114 mm and inside diameter of d=102 mm supports the loads shown in the figure 1. Determine  a) the normal and shear stress acting at point H and show these stress element  b) the principal stress and planes and show these stress element c) the maximum shear stress and planes and show these stress element

Q: Q2: For the element shown in Figure 2. Use the data from Table 2 Determine the following: 1. The…

A:

Q: In the figure below, the arm CD of the pipe is parallel to the z axis. The cross-section of the pipe…

A: Given Data:Inner radius of Pipe Outer radius of Pipe Find:(A) Stresses on point A(B) Stresses on…

Q: a Steel pipe with an outside with an outside diameter of 100mm and inner diamete of 90mm is…

A:

Q: Find the normal stress and shear stress in the c-plane for the stressed member shown in the figure.…

A: Given figure    To determine the normal stress and shear stress in the c-plane for the stressed…

Q: iven an element with stresses as indicated in figure below, find the following: a) The maximum and…

A: Given: The shear stress acting on the element = -35 kPa The normal stress along the x-axis = 20 kPa…

Q: Problem 2: The stresses shown act at a point on the free surface off a stressed body. a) Determine…

A:

Q: 450 kN and 100 kN forces were applied to the recessed beam shown in the figure. Find the stresses at…

A:

Q: 3. A 65 mm diameter solid shaft is subjected to force and torque as shown in the figure below.…

A: Given, Diameter, D=65 mm,Cross-section Area, A=π4D2A=π4652A=3318.307 mm2 Calculate the stress due to…

Q: In the figure, the normal stresses oa = 70 MPa, o, = 50 MPa, oc = 110 MPa on the faces of the…

A: Given that, σa=70 MPa,σb=50 MPa,σc=110 MPa,α=60°,β=45°, The general form of the equation of stress…

Q: 4 - A rectangular block is loaded with a 180 kN axial force and a moment M, as shown in the figure.…

A: Given data:-  Axial force =180 kN the maximum allowable tensile stress = 50 MPa To find:- the…

Q: Complete answer

A: Given Data: Diameter of OB and AB (D) = 100 mm = 0.1 m Radius of disc (r) = 0.5 m Allowable normal…

Q: In the figure, a force of 1 kN is applied by means of an arm connected to a shaft with a diameter of…

A: Now, calculate the torque due to 1 kN force, T = 100 x 1 kN = 100 kN-m Bending moment due to 1 kN, M…

Q: Given an element with stresses as indicated in figure below, find the following: a) The maximum and…

A: “Since you have posted a question with multiple sub parts, we willprovide the solution only to the…

Q: the direction where the normal stress is zero

A:

Q: C ):- Draw the MC stress elemen Find:-

A: given:σX=20ksiσy=14ksi

Q: cresses at A and B points according to the ven and show them on the stress element.

A:

Q: a state of stress at a point in a member defined by the element shown in the figure. Find the main…

A:

Q: B = 30° A 50 mm

A: The moment of inertia about the y-axis and z-axis are determined as follows.

Q: Given a stress element in the figure, find the planes in which the normal stresses are equal in…

A:

Q: The steel bar in the figure has a diameter of 60 mm. As the shaft is loaded with the CDE rigid arm…

A: Given: Diameter of the steel bar is 60 mm. The loaded shaft is shown below:

Q: Given an element with stresses as indicated in figure below, find the following: a) The maximum and…

A: “Since you have posted a question with multiple sub parts, we willprovide the solution only to the…

Q: Oy = 90MPA %3D Try 60MPA %3D Ox=20MPA

A: Given Data Normal stresses σx= 20MPa σy=90MPa Shear stress fxy=60MPa   Main stresses are the…

Q: section shown in figure Question 2, determine the shear stress a. In the Web at point A b. and in…

A:

Q: In the figure, a force of 1 kN is applied by means of an arm connected to a shaft with a diameter of…

A:

Q: For the plane stress case in the figure, a) the direction in which the normal stress is zero, b)…

A: Given data: σx =7 N/mm2 σy =7 N/mm2 τxy =24 N/mm2 Need to determine the the direction in which the…

Q: 3. An element in plane stress on the fuselage of an airplane (figure part a) is subjected to…

A:

Q: A structural member is subjected to the plane stress condition. The state of stress at a point of…

A: Given conditions; ζxy=9 MNm2 σx=-12 MNm2( compressive in nature). σy=16 MNm2(tensile) Principal…

Q: Consider the circular bent rod with diameter 20 mm. The free-end of the bend is subjected to loads…

A:

Q: The state of stress on an element is shown in following figure. i) Determine the stresses acting on…

A: Given Data  σx=42MPa σy=140MPa ζxy=60MPaθ=48(°ccw) To find  1. The resultant stress  in second plane…

Q: - Draw the Mohr's Circle of the stress element shown in figure. Find: - The stresses acting on…

A: the following data is given-

Q: The screw clamp shown in the figure applies a P = 500 N pressing force to the wooden blocks between…

A: We have to determine  a) Calculate the greatest tensile and compressive stresses occurring in the…

Q: according to the given and show them on the stress element.

A:

Q: The state of plane stress at a point on the surface of the airplane fuselage is represented by the…

A: To find-  1. The maximum principal stresses and the maximum in plane shear specifying the…

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.