A venturiflame is 1.3 m wide at entrance and 0.65m in the throat.Neglecting hydraulic losses in the flume, calculate the flow if the depths at the entrance and throat are 0.65m and 0.6 m respectively.A hump is now installed at the throat of height 200mm,so that a standing wave (hydraulic jump)is formed beyond the throat.What is the increase in the upstream depth when the same flow as before passes through the flume?

A venturiflame is 1.3 m wide at entrance and 0.65m in the throat.Neglecting hydraulic losses in the flume, calculate the flow if the depths at the entrance and throat are 0.65m and 0.6 m respectively.A hump is now installed at the throat of height 200mm,so that a standing wave (hydraulic jump)is formed beyond the throat.What is the increase in the upstream depth when the same flow as before passes through the flume?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Mild steel 1 Young;s modulus 1219.5 Yield strain and stress (0.4101,500.08) Failure stress and strain :not able to find because the given data shows the experiment did not reach the failure point. if the material stress and strain does not reach a failure point ,what dose it means , does it means that the material is more stronger?
Water flows in a rectangular channel that is 0.5 m wide as shown. The upstream depth is 70 mm. The water surface rises 40 mm as it passes over a portion where the channel bottom rises 10 mm. If viscous effects are negligible. What is the flow rate? (2) 100 mm (1) 70 mm 10 mm
QUESTION 4 Water flows in a rectangular channel at a depth of y₁ = 0.2 m and a flow rate of 7.5 m³/s. A hydraulic jump is generated and the width of the channel is 4 m. Chezy's roughness constant for the channel is 56 SI units. Determine: 4.1 the depth downstream 4.2 the Froude number downstream 4.3 the head loss in the jump 4.4 the bed slope
The water flows in the channel with a base slope of 0.003 and the cross-section shown in Figure 3. The dimensions of different subdivisions and the Manning coefficients for surfaces are also shown in the figure.a) calculate the volume flow flowing through the Channel.B) calculate the Manning coefficient.
Consider gradually varied ﬂow of water in a 20-ft wide rectangular channel with a ﬂow rate of 300ft3/s and a Manning coefﬁcient of 0.008. The slope of the channel is 0.01, and at the location x = 0, the mean ﬂow speed is measured to be 5.2ft/s. Determine the classiﬁcation of the water surface proﬁle, and, by integrating the GVF equation numerically, calculate the ﬂow depth y at (a) x = 500ft, (b) 1000ft, and (c) 2000ft.
A hydraulic jump is shown in figure below. The depth of flow z₂ after the hydraulic jump is 5 m larger than z₁. The total flow rate in the channel is 450 m³/s and the channel width is 50 m. The length / over which the jump occurs is 0.4 m. ax= If the depth, z₁, is 6 m then what is the average acceleration (ing's) of the liquid as is flows across the jump. 0.21 Hydraulic jump g's V₂
Find the discharge value Area=0.9 m2 Velocoty=0.2 m/s
Water flows in a rectangular channel with a width of 2.5 m. The kinetic energy correction coefficient (i.e. velocity coefficient) is estimated as a = 1.2. If the flow rate is 5 m³/s and the flow depth is 1.5 m: (a) determine the specific energy of the flow. (b) Calculate the alternate depth considering α = 1.0.
Water flows half-full through a 38-cm-diameter steel channel at an average velocity of 2.3 m/s. Determine the volume flow rate and whether the flow is subcritical or supercritical.
In flowing from section (1) to section (2) along a rectangular open channel, the water depth decreases by a factor of three and the Froude number changes from a subcritical value of 0.7 to a supercritical value of 3.4. Determine the channel width at (2) if it is 8 ft. wide at section (1). Assume stead-state flow.
A triangular open-channel (n=0.014) has a side slope of 4H:5V. The flow depth is 1.5m when the slope is 0.002. Determine the volumetric flowrate.