(i) A channel is formed by having two vertical brick walls with a semi circular culvert at thebottom. It is found to discharge 301 m3/s of water, determine the height from the culvert,of the wetted part of the brick walls at critical conditions(ii) If the stream function of a two dimensional flow is x²+2x2-2y, determine if the flowexists and irrotational. Determine the velocity potential

As per the guideline, I can solve only first question. For second question, repost in a separate…

A channel is formed by having two vertical brick walls with a semi circular culvert at the bottom. It is found to discharge 301 m3/s of water, determine the height from t of the wetted part of the brick wallo

A channel is formed by having two vertical brick walls with a semi circular culvert at the bottom. It is found to discharge 301 m3/s of water, determine the height from t of the wetted part of the brick wallo

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

88 cm d 17 cm In the fountain shown, water flowing at 35 lpm exits the weir at the top, with a stream that is 17 cm wide and 0.20 cm thick. Determine the diameter of the stream (cm) at a point 88 cm below the weir, assuming that the flow has a cylindrical shape at this location Solution: 1.3 cm
Question Water is draining from the bottom of a cone- shaped funnel at the rate of 0.8 ft³/sec. The height of the funnel is 6 ft and the radius at th top of the funnel is 5 ft, as shown in the imag below. At what rate is the height of the water the funnel changing when the height of the w is 4 ft? Submit an exact answer in terms of л. Provide your answer below: dh dt ft/sec 5
The figure shows a channel with width of 2.4 m. The density of the water is 1000 kg/m^3. The flow is steady. At the entrance of the channel, the flow is uniform with velocity V (m/s) while at the exit, the flow has developed the shown velocity profile u(y) = 4y-2y^2 (m/s) and y is in (m). Answer the following questions. The area in (m^2) of the entrance is: V 0.75 u = 4y – 2y? The area in m^2 at the exit section is: The average velocity in (m/s) at the exit section is:
In order to determine the flow in a rectangular channel, a 75-mm-high bump is added on its bottom surface. The measured depth of flow at the bump is 1.25 m. The flow is uniform throughout the cross-sections at A and B, and the channel has a width of 1.2 m. Assume the fluid is an ideal fluid, that is, incompressible and frictionless. B 1.25 m 1.5 m 75 mm Part A Determine the volumetric discharge. Express your answer to three significant figures and include the appropriate units.
Water is discharged from a reservoir into the atmosphere through a 80 m long pipe. There is a sharp entrance to the pipe and the diameter is 250 mm for the first 50 m. The outlet is 35 m below the surface level in the reservoir. The pipe then enlarges suddenly to 450 mm in diameter for the reminder of its length. Take f 0.004 for both pipes. Calculate the discharge.
2 1.3 m 1 3.3 m 6 cm - diameter 3 Group (A) Determine the discharge, the velocity of flow and pressure at the point (2)?
60 kpa Q.2. Oil flows steadily through the pipe shown in Figure. If the flux through the pipe is 350 liters per second, then determine the total energy at point A and point B? Which one is the largest? Comment on whether the results are acceptable or non-acceptable? (Specific gravity of oil = 0.95 and the density of water = 1000 kg/m³) A. 40 cm 4 m 100 kpa 35 emf 80
Question 2. An incompressible fluid flows steadily in the entrance region of a two dimensional channel of height 2h. Density of the fluid is 1.24 kg/m3. The uniform velocity at the channel entrance is U1=5.3m/s The velocity distribution at a section downstream is: 1- ()* и Umax Find out the maximum velocity umax in the downstream section in (m/s).
7. For the flow of a thin layer of liquid down an inclined plane shown: a. Using the cross-hatched element and through a force balance, show that the velocity distribution across the layer is: dx y sin e (b2 - s2) 2 u Free Surface b. Derive an expression for the liquid velocity at the free surface. t dx Fixed ys dx c. Derive an expression for the discharge per unit width. d. Derive an expression for the shear stress at the fixed wall. Wall
Water flows steadily along a horizontal open channel of uniform width, over a broad-crested weir. The channel bed upstream from the weir (to the left) is d metres above the channel bed downstream from the weir (to the right), as shown in the figure below. The volume flow rate per unit width is Q = 6 m? s-1, and upstream the depth of the water is h1 = 3 m. Take the magnitude of the acceleration due to gravity as g = 10 ms 2. hi D p. h2 U2 (a) Find the upstream speed u1, and show that the flow is subcritical there. (b) Find the specific energy E (in m) for the flow upstream. (c) By applying Bernoulli's equation along a suitable streamline, show that the depth h2 in the downstream section of the channel satisfies the equation 5h – (16 + 5d)h+9 = 0.
60m 44m (2) (1) (3) 40m (4) 40m (5) 42m c) Find the flow discharge within the system. (6) 30m 35m Q (2). You have a tank open at the top, flow in the 25-cm-smooth-65 m long- plastic pipe. (7)
Reservoir and parallel disks flow system. The solution should be carried out using cylindrical coordinates. Water escapes out of the gap "h" around the whole circumference 1)At what volume flow rate Q(r0, r2, g, H,h) should the tank at (0) be refilled to maintain constant water level? and what does the resulting expression reduce to if 2h<