A vehicle of mass 21 tonnes runs into a buffer stop having two buffer springs connected in series each of 1300 kN/cm and 2100 kN/cm stiffness respectively. Find the maximum compression of the springs, if the vehicle is travelling at 115 km/hr. Also calculate the load acting on the spring. The maximum compression of the spring in mm is The load acting on the spring in kN is

A vehicle of mass 21 tonnes runs into a buffer stop having two buffer springs connected in series each of 1300 kN/cm and 2100 kN/cm stiffness respectively. Find the maximum compression of the springs, if the vehicle is travelling at 115 km/hr. Also calculate the load acting on the spring. The maximum compression of the spring in mm is The load acting on the spring in kN is

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.50P: The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the...

See similar textbooks

Similar questions

The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016, determine the force F required to advance the bar at a constant speed.
If PCD=6000lb and PGD=1000lb (both compression), find P and Q.
The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the smallest force P and the corresponding angle that would cause impending sliding of the block. The angle of static friction between the block and the ground is s.
A truck of mass 3 tonnes runs into a buffer stop having three buffer springs each of 40 kN/cm stiffness connected in parallel. Find the maximum compression of the springs, and the load if the wagon is travelling at 60 kmph. 1-Equivalent Stiffness of spring in kN/mm is 2-Kinetic Energy in kNmm is 3-The maximum compression of the spring in mm is 4-Load acting on the spring in kN is
A truck of mass 1 tonnes runs into a buffer stop having three buffer springs each of 15 kN/cm stiffness connected in parallel. Find the maximum compression of the springs, and the load if the wagon is travelling at 110 kmph. Equivalent Stiffness of spring in kN/mm is Kinetic Energy in kNmm The maximum compression of the spring in mm Load acting on the spring in kN is
A truck of mass 2 tonnes runs into a buffer stop having three buffer springs each of 10 kN/cm stiffness connected in parallel. Find the maximum compression of the springs, and the load if the wagon is travelling at 110 kmph.
Calculate the rection forces when the radius of the pulleys are 0,1 m and K = 1200 N.
(b). A truck of mass 17 tonnes runs into a buffer stop having two buffer springs connected in series each of 1450 kN/cm and 2600 kN/cm stiffness respectively. Find the maximum compression of the springs, if the truck is travelling at 90 km/hr. Also calculate the load acting on the spring.
in the system shown, the bar AB can withstand a tension of 4.90 kN, and a compression of 2.53 kN; the spring constant k is 2.85 kN / m, the spring's undeformed length is 0.433 m, the mass of W is 365 kg, and the force P makes an angle of 60 ° with the horizontal. Calculate the stretched length of the spring and the magnitude of the force P so that:- The bar fails due to tension- The bar fails due to compression NOTE 1: For the direction of the force P do not be guided by the drawing. The force P can point in any direction (all 4 quadrants) as long as it maintains the indicated angle with respect to the horizontal.
A beam with a length of 2 m and a mass of 10 kg supports a 50 kg box. The beam is connected to a wall by a hinge at its base and a horizontal wire. The wire is connected to the beam 1.5 m from the hinge and makes an angle θ of 35o to the beam. The goal is to find the tension in the wire and the horizontal and vertical components of the force exerted by the hinge on the board Calculate the tension in the string. write down Newton’s 2nd law for both x and y directions. find the horizontal and vertical components of the force that the hinge exerts on the beam. Suppose the maximum tension that the wire can withstand is 1500 N. What is the maximum load that the hinge can support before the wire breaks?
You need to move a cubic crate across a rough floor. You pull the crate horizontally using a rope with force F, as shown in Figure 1. The weight of the crate is 700 lb:, its density is 180 lbm/fts, and the coefficient of static friction between the crate and the floor is 0.57. Write an expression for the maximum static friction force fmax (in lb:) as a function of the mass m of the crate. Use Excel to plot fmax(m). Calculate the average pressure of the crate on the floor, in psi. Calculate the minimum force F necessary for the crate to start moving, in lb;. F Figure 1. Moving a crate on a slope.
7. A compound lever as shown below. Find the effort P. if the system is used to lift a mass of 800kg. (10) S00 mam 400 mm 350 mm S0mm 800 kg 8. An oil drum 600mm in diameter and length Im is to be rolled over a step 120mm in height. Find the least pull through the centre of the drum required just to turn the drum over the step. Also find the reaction on the step. Assuming all the surfaces to be smooth. Take density of oil as 1 kg/litre and neglecting weight of the drum. (10) 50 mm