A vehicle having a mass of 1000 kg passes on a road bump. The resulting displacement-time curve is indicated in the following figure. xe[cm] t(s) 0.2 Find the natural frequency in rad/s.

Q: Which of the following statement is correct Select one: Friction causes objects to slip down…

A: Friction force is directly proportional to the normal force acting to body and independent of area…

Q: Why is it important to determine the slopes and displacements?

A: Slope – when ever any load is applied on the beam due to its elastic properties it bend in very…

Q: Impact velocity equation

A:

Q: Give an example of concentrated force.

A: Whenever total magnitude of a force act on a single point then this type of loading on a beam is…

Q: What are internal forces?

A: Internal forces are defined as the forces exerted by the particles of the body on each other within…

Q: Which of the following part designs would be preferred because it would result in lower production…

A: To be explained:- which method will give lower cost

Q: Indicate the following technical tolerance requirements in Fig.3. a) The diameter of the middle…

A:

Q: Statics; working

A:

Q: What functional problem results from torsion?

A: Given:What functional problem results from torsion?

Q: The type maintenance requires periodical inspection and testing.

A: Preventive maintenance/periodic maintenance/ planned maintenance is driven by time, meter or event…

Q: What is damped Vibration.

A: Given Data : damped Vibration.

Q: What is angular indexing and block indexing?

A: Angular indexing:  It is similar to simple indexing except that in this process, instead of rotating…

Q: at are some formulas used in GD

A: GD& T:- A symbolic language known as GD&T, or geometric dimensioning and tolerancing, is…

Q: Which organization sets the standards for dimensioning and tolerancing practices?

A: Given Data⇒ standards for dimensioning and tolerancing practices Problem statement⇒ Problem says…

Q: Please answer print reading for industry 15-1 # 9, 12, and #15

A: 1) Yes, It is the detailed drawing of one part. This drawing do not have bill of material table. 2)…

Q: tan30*sin30

A: Given, Value of tan30 and sin30 is, tan30°=0.577sin30°=0.5

Q: What is load-displacement?

A: It is related to a ship or a cargo vessel.

Q: What do the Discontinuity functions express?

A: A discontinuity function expresses that at the point of discontinuity either the limit doesn’t exist…

Q: What is planar motion?

A: Planar motion is the kind of motion where a body moves in a plane and has two degrees of freedom,…

Q: Name 3 types of fits?

A: The different types of fits are : 1) Clearance fit 2) Interference fit 3) Transition fit

Q: how do i find, Vba; Vbc; Vbd?

A:

Q: What is the basic unit for length?

A: Solution Length → The measurement of something from end to end is called length

Q: What is statically balance forces

A:

Q: Determine, using the principle of superposition, the reactions at supports A and B for equilibrium.…

A:

Q: When does a couple of moment work?

A: A couple is when a system of forces has no net force but has a net moment. A couple causes pure…

Q: Rolling friction occurs when one surface slides over another surface  Select one: True False

A: Rolling friction is seen between the two surfaces which are in rolling.contact

Q: QI Define five of the following with sketch. 3- AA2024 4- Rolling 5- Wire drawing 1-Taper turning 2-…

A: Taper turning is a turning technique in which the cutting tool travels at an angle to the…

Q: What is compound indexing?

A: Soln:- Compound indexing :- Compound indexing is the operation of obtaining a desired spindle speed…

Q: On the attached drawing, is the allowance between "shaft C" and "hole D" positive or negative?

A: Allowance is the difference between the basic dimensions of the mating parts. There are two types of…

Q: This is used tO correspond with machine tool usage where a working stroke would have high force…

A: ANSWER IS OPTION [ D] QUICK RETURN MECHANISM EXPLAINATION = QUICK RETURN MECHANISM IS USED IN…

Q: What is damping Vibration.

A: Given Data : damped Vibration.

Q: Describe the method of sections?

A: Method of section In this method we deal with the non-concurrent forces. Here, we get three…

Q: For each of the mating part pairs below, and lower limit for each part. For A and B, səddn express…

A:

Q: 7. How many ½ inch diameter set-screws would be required to transmit 3 horsepower at a shaft speed…

A:

Q: What is tapping

A: Handwriting.jpg

Q: What is called the fit? 1) the difference between the maximum and minimum limits of size, 2) the…

A: Handwritten.jpg

Q: Which of the following is NOT true of a lever: O it changes the magnitude of the force O it changes…

A:

Q: what is the value of Cx?

A: Fx= 12.662 kN. Using equilibrium condition in x direction for member FC.

Q: This was not correct may you please

A:

Q: es the specification "8.8" in the standard designation of a bolt mean? Specify values including…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…