A uniform plane wave in air with E(z, t) = âx 20 sin (10°t - B1z) (V/m)is incident normally on a lossless medium (E2 = 9, µr2=1, 0 = 0) in theregion z>0.TransmittedWaveReflectedWaveE,Find :Eâ,a) B1 and B2 i.H,b) T (Reflection Coefficient)c) T (Transmission Coefficient)E;yd) Ē,(z,t) (Reflected E-Field)e) H¿(z,t) (Transmitted H-Field)IncidentWaveHiMedium-1Medium-2Eo , Hoε 980, μο , σ 0Z= 0

Given: A uniform plane wave in air with Ei→=ax^20sin108t-β1z V/m is incident normally on a lossless…

A uniform plane wave in air with E;(z, t) = âx 20 sin (10° t - B,z) (V/m) is incident normally on a lossless medium (E2 = 9, µr2=1, 0 = 0) in the region z>0. Transmitted Wave Reflected Wave E, Find : E â, a) B1 and B2 { H, H b) T (Reflection Coefficient) c) T (Transmission Coefficient) d) Ē„(z,t) (Reflected E-Field) e) H¿(z,t) (Transmitted H-Field) E. y Incident Wave H Medium-1 Medium-2 Eo . Ho E2 = 9 E0 , Ho , o = 0 Z = 0

A uniform plane wave in air with E;(z, t) = âx 20 sin (10° t - B,z) (V/m) is incident normally on a lossless medium (E2 = 9, µr2=1, 0 = 0) in the region z>0. Transmitted Wave Reflected Wave E, Find : E â, a) B1 and B2 { H, H b) T (Reflection Coefficient) c) T (Transmission Coefficient) d) Ē„(z,t) (Reflected E-Field) e) H¿(z,t) (Transmitted H-Field) E. y Incident Wave H Medium-1 Medium-2 Eo . Ho E2 = 9 E0 , Ho , o = 0 Z = 0

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A sinusoidal wave on a transmission line is specified by voltage and current in phasor form: Vs(z) = Voeaz ejßz and Is(z) = 1,eaz ejßzejp where Vo and I, are both real. a) In which direction does this wave propagate and why? b) Consider that a = 0, Zo 500, and the wave velocity is v, = 2.5 × 108 m/s, with w = 108 s-1. S Find the resistance (R), the admittance (G), the inductance (L), the capacitance (C), the wavelength (1) and the current phase ().
A 2 V signal is incident to the interface from a 75 Ohm region propagating to a 50 Ohm impedance region. What is the reflection coefficient? What is value of the incident, reflected and transmitted wave? What voltage would you measure on either side of the interface right after the signal goes through the interface. For the interface, I'm a little confused. I used a voltage divider and got V_transmitted = 0.8 and V_incident = 1.2. But shouldn't they be the same?
COS (2T10 Problem 4. A voltage wave of the form V+ = (2x 10-4V) cos( t-kz is incident from cable 1 with characteristic impedance 201 = 1200 onto a connection to cable 2 with characteristic impedance Z02=1002. Take the speed of the cable wave in each cable to be 2 x 10 m/s. A) Find the amplitudes of the reflected and transmitted voltages. B) Find the incident, reflected, and transmitted powers.
Derive the expressions for the Ex, Ey, Bx, By in Waveguides. Pls. show complete answer
1. Matching of a transmission line with a characteristic impedance (Zo) and a load impedance (Zn) can be obtained when (a) ZR 0.5Zo (b) ZR=2Zo (c) ZR-Zo (d) ZR-0 2. Standing wave ratio (S) for a short circuit load connected to a transmission line is equal to (a) S=0 (b) S= -1 (c) S= Infinity (d) S=1 3. Any transmission line repeats its impedance, voltage, and current characteristics every . (Where n-0, 1, 2, 3....etc.) (a) nλ/2 (b) nλ/3 (c) ni/5 (d) n2/6
1. Matching of a transmission line with a characteristic impedance (Zo) and a load impedance (ZR) can be obtained when (a) ZR=0.5ZO (b) ZR-2Z0 (c) ZR-Zo (d) ZR=0 2. Standing wave ratio (S) for a short circuit load connected to a transmission line is equal to (a) S=0 (b) S=-1 (c) S= Infinity (d) S=1 3. Any transmission line repeats its impedance, voltage, and current characteristics every (Where n-0, 1, 2, 3....etc.) (b) nλ/3 (a) nλ/2 (c) ni/5 (d) nλ/6 4. In smith chart, moving in the clockwise direction means moving a) From load to generator b) From generator to load 5. In Crank diagram, moving in the clockwise direction from the load to the source can be evaluated using the formula a) +j2Bd b)-j3Bx c) -j2Bd d)-j2Bx
a- define a shield b- calculate Reflection loss in dB for a plane wave incident in a shield with impedance |Z,| 50 N c-calculate the absorption loss in dB for a shield with thickness t= 0.2 inch and skin depth of 0.05 inch
مودود WIDTH ch7 for the cable. A wave traveling in a lossless, nonmagnetic medium has an electric field amplitude of 24.56 7-31 V/m and an average power density of 2.4W/m². Determine the phase velocity of the wave. 2-4
A rectangular copper block is depth d along z, width w along y, and length / along x. In response to a wave incident upon the block from above, a current is induced in the block in the positive x-direction. Determine the ratio of the ac resistance of the block to its dc resistance at frequency f. 0: 5.8.107.- S m /:=1.2 m d: 40 cm W: 50 cm f:=2 kHz
An EMF source has an internal impedance of 100+ j0 ohms, and EMF of 3 V. Using Zo = 50 , find the reflection coefficient and scattering variable for the source.
A wave guide in non magnetic medium with a= 2.28cm,b=1.01cm ,ɛ, =2.25. Find cutoff frequency for TE11 mode
What are reflection and transmission coefficients? Derive the formula for the same. When an EM wave travels from a dielectric (medium-1) to the conductor,then what will be the value of these parameters?