1. Matching of a transmission line with a characteristic impedance (Zo) and a load impedance (Zn) can be obtained when (a) ZR=0.5Zo (b) ZR-2Zo (c) ZR-Zo (d) Z-0 2. Standing wave ratio (S) for a short circuit load connected to a transmission line is equal to (a) S=0 (b) S=-1 (c) S= Infinity (d) S=1 3. Any transmission line repeats its impedance, voltage, and current characteristics every . (Where n-0, 1, 2, 3....etc.) (a) n)/2 (b) 12/3 (c) nλ/5 (d) n2/6

1. Matching of a transmission line with a characteristic impedance (Zo) and a load impedance (Zn) can be obtained when (a) ZR=0.5Zo (b) ZR-2Zo (c) ZR-Zo (d) Z-0 2. Standing wave ratio (S) for a short circuit load connected to a transmission line is equal to (a) S=0 (b) S=-1 (c) S= Infinity (d) S=1 3. Any transmission line repeats its impedance, voltage, and current characteristics every . (Where n-0, 1, 2, 3....etc.) (a) n)/2 (b) 12/3 (c) nλ/5 (d) n2/6

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q4) A- For the following SWR Pattern, find the reflection coefficient of the load and Ag . -8.6 43 - mm.i- 80. Bo 140 B- Draw the SWR pattern for a matched load, comment on that pattern.
A 2 V signal is incident to the interface from a 75 Ohm region propagating to a 50 Ohm impedance region. What is the reflection coefficient? What is value of the incident, reflected and transmitted wave? What voltage would you measure on either side of the interface right after the signal goes through the interface. For the interface, I'm a little confused. I used a voltage divider and got V_transmitted = 0.8 and V_incident = 1.2. But shouldn't they be the same?
Q1/4 Choose the correct answers and fill the blanks for the following questions: 1. Matching of a transmission line with a characteristic impedance (Zo) and a load impedance (ZR) can be obtained when (b) ZR-2Z0 (a) ZR-0.5Zo (c) ZR-Zo (d) ZR-0 2. Standing wave ratio (S) for a short circuit load connected to a transmission line is equal to (a) S=0 (b) S=-1 (c) S=Infinity (d) S-1 3. Any transmission line repeats its impedance, voltage, and current characteristics every (Where n-0, 1, 2, 3....etc.) (b) nλ/3 (a) nλ/2 (c) nλ/5 (d) nλ/6 4. In smith chart, moving in the clockwise direction means moving. a) From load to generator b) From generator to load 5. In Crank diagram, moving in the clockwise direction from the load to the source can be evaluated using the formula a) +j2Bd b)-j3Bx c) -j2Bd d)-j2ßx 6. For a lossless transmission line operating with frequency 300MHz, and it has an inductance L-30mH/unit of length and a capacity C-75 µF/unit of length, the while the phase constant (B) is…
In non-sinusoidal wave sources, the dissipated power in the load is depends on the value of . . Variable Current Average Current Constant Current All-of-them
A coaxial cable with a characteristic impedance of 50 Ohm is used to deliver mi- crowave signal to a TV antenna which has an impedance of 75 Ohm. What fraction of the signal (in terms of power) can be coupled into the antenna?
b) 1) Design (Find R₁, RF, and R) the sawtooth-wave generator to have an output frequency fo = 6kHz. Assume Vth = |- Vth = 5V, Vsat = |-V sat | = 14V, and Vref= -9V.Assume the value of C = 0.04µF. 2) Determine duty cycle (k). 3) Draw the design circuit and output waveform.
For, z=0.1 and Wn= 5: Peak amplitude = 1.53 Settling time * 7.6 seconds true O False
Sketch/Draw the following: a. 100% modulation trapezoidal pattern b. Negative Carrier Shift c. Envelope of a square wave modulating a sinusoidal carrier
Imagine a two-dimensional system in which a sinusoidal waveform is excited at the exact center of a circular plate. The standing wave pattern is established when the excited wave two-dimensionalwaveforms for a stable equilibrium pattern of constructive and destructive interference with the reflected waves from the edge of the circular plate. Draw what you expect the standing wave patterns to look like in this two-dimensional system for increasing resonant harmonics, n. Explain what characteristics of the oscillating plate affect the value of those resonancefrequencies, and what geometric properties of the plate affect the patterns.
1. Matching of a transmission line with a characteristic impedance (Zo) and a load impedance (ZR) can be obtained when (a) ZR=0.5ZO (b) ZR-2Z0 (c) ZR-Zo (d) ZR=0 2. Standing wave ratio (S) for a short circuit load connected to a transmission line is equal to (a) S=0 (b) S=-1 (c) S= Infinity (d) S=1 3. Any transmission line repeats its impedance, voltage, and current characteristics every (Where n-0, 1, 2, 3....etc.) (b) nλ/3 (a) nλ/2 (c) ni/5 (d) nλ/6 4. In smith chart, moving in the clockwise direction means moving a) From load to generator b) From generator to load 5. In Crank diagram, moving in the clockwise direction from the load to the source can be evaluated using the formula a) +j2Bd b)-j3Bx c) -j2Bd d)-j2Bx
A 60-2 transmission line is connected to a 75-2 resistive load. If the incident voltage is 5 V rms, then the reflected voltage is: a) -1.026 Vrms. b) -0.832 Vrms. c) 0.556 Vrms. d) 1.569 Vrms. e) 2.320 Vrms.
Why is the negative effect of stray capacitance more pronounced in very high frequency circuits?