A uniform load 119 kN/m is acting downward and supported by an upward uniform pressure of 51 kN/m as shown in the figure below. 1.0m 1.5m 2.0m 1.5m 1.0m 119 kN/m 119 kN/m 51 kN/m Which of the following give's the maximum shear in the beam? Select the correct response: 51 kN 84 kN 32 kN 48KN Continue > < Previous

A uniform load 119 kN/m is acting downward and supported by an upward uniform pressure of 51 kN/m as shown in the figure below. 1.0m 1.5m 2.0m 1.5m 1.0m 119 kN/m 119 kN/m 51 kN/m Which of the following give's the maximum shear in the beam? Select the correct response: 51 kN 84 kN 32 kN 48KN Continue > < Previous

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

20 KN A 12.7 ZU Draw the graphs of the axial -3 forces, shear forces and bending moments for the beam shown in the figure below, then choose the :appropriate value for the following 3m 32.7 20 KN B clear selection 3m 16 KN/m C 5m 20 215.6 141. OC D Axial force at point B bending torque The reaction in the predicate A Shear strength in the middle of the sill
mm on its side, just 2. A cantilever, made of a certain material, of 2 m length and square section fails in bending when a point load of N is placed at its free end. A beam of rectangular cross section, and made of same material, 150 mm wide and 300 mm deep, is simply supported over a span of 3 m. Calculate: (a) the stress at which the cantilever beam fails in kPa and (b) the maximum concentrated load that the beam can carry at its center without failure in kN. 2 m (a) Cantilever kN THIS |— 1.5 m —— 1.5 m—| (b) Simply supported beam 150 300
Determine the maximum shear stress in the T-beam at point C. 150 mm 10 kN/m T 150 mm 30 mm |C --30 mm 5m +₁. 3 m- -1.5 m-1.5 m- A B
Determine the maximum compressive stress in the beam which is subjected to the 20-kN/m uniformly distributed load over half of its length. A 20 kN/m 2 m 2 m B so 60° 180 mm 120 mm 160 mm 200 mn
A В A uniformly distributed load is applied on a simply supported beam. What is the Maximum Shear (in kN) experienced by the beam? w = 30 kN/m L= 4.1 m w/
A solid 0.78-in.-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the shear stress magnitude in shaft (3). a.)3.86 ksi b.) 3.51 ksi c.) 3.15 ksi d.) 5.38 ksi e.) 4.85 ksi
please answer in the nearest 3 decimal numbers
A wooden beam 150mm wide by 300mm deep is loaded as shown. If the maximhm flexural stress is 8MN/m^2. Find the maximum values of1.)W(kN/m)2.) P (kN)
show all work clearly organized
The beam loaded as shown is rectangular in cross-section having a width of 250 mm and a depth of 400 mm. Determine the following: 12KN/m 10KN/m 5m 3m a. The maximum flexure stress developed For the reaction at the supports - For the correctly drawn shear diagram (including location of zero shear For the correctly drawn moment diagram( including the magnitude of maximum moment) For the maximum stress developed b. *The stress developed at the fiber 50 mm from top of the beam, 3 meters to the right of support at A For the magnitude of moment at the section being considered For the magnitude of the stress