A simply supported beam is subjected to a linearly varying distributed load q(x) = q, with maximum intensity q, at B. The %3D beam has a length L = 4 m and rectangular cross section with a width of 190 mm and height of 320 mm. 9(x) A В Determine the maximum permissible value for the maximum intensity, go, (in kN/m) if the allowable normal stresses in tension and compression are 145 MPa. kN/m

A simply supported beam is subjected to a linearly varying distributed load q(x) = q, with maximum intensity q, at B. The %3D beam has a length L = 4 m and rectangular cross section with a width of 190 mm and height of 320 mm. 9(x) A В Determine the maximum permissible value for the maximum intensity, go, (in kN/m) if the allowable normal stresses in tension and compression are 145 MPa. kN/m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3. (c) A square steel bar of dimension 50 mm × 50 mm × 150 mm is subjected to an axial load of 250 kN. Determine the decrease in length of the bar if (i) the lateral strain is fully prevented by applying external uniform pressure on the rectangular surfaces
The simply supported composite beam below is made by bolting two wood boards (E = 1,900 ksi) to the sides of a steel plate (E = 29,000 ksi), as shown below. (A) Determine the max. and min. normal stress in the steel plate and the wood boards. (B) Sketch the bending strain and stress distribution over the width of the beam's cross-section. 0.5 in 600 lb/ft 12 in 6 ft 12 ft 6 ft → 3in 3in
350mmi The simply supported beam has an I-shaped cross section. (1) Determine the values and locations of the maximum tensile and compressive bending stresses. (2) Sketch the bending stress distribution over the cross section on which the maximum bending stress occurs. No credits if free body diagram is not present. 0 35m 11mm 8 kN/m 100 kN 7.5mm 11mm 0.8 m 2 m 54 1.0m 175mm 1100KN
A beam with the cross-section shown is subjected to a vertical shear of 28 kN. Determine: (a) the largest shearing stress in that section. (b) the shearing stress at Point a. 65 mm 100 mm -210 mm 8 mm 200 mm 8 mm T max = T@a= kPa kPa
Figure Q3 (a) shows a cantilevered beam ABC carrying a pure moment of M kN.m at point B. Thecross-sectional area of the beam is shown in Figure Q3 (b). The yield stress of the material is 250 MPa and the material is assumed to behave linearly elastic-perfectly plastic.a) Where is the critical location for the beam and give ONLY ONE (1) reasonb) Determine the moment to initiate yielding in the cross-section of the beamc) Find the value of M that can cause plastic collapse (fully plastic) in the cross-section of the beamat the critical location and sketch the variation of stressd) If the TOTAL DEPTH of the plastic zone to be 20 mm at the critical location, WITHOUT ANYCALCULATION, sketch the variation of stress.
In the figure, find the length c of the overhangs so that the beam made of U profile can carry the loading safely. The safety stress (σç)emn=50N / mm2, (σb)emn=80N /mm2 for the tensile and compression condition of the material. The support range of the beam is L=6 m, cross-section dimensions a=210 mm, b=150 mm and wall thickness t=40 mm. The loading condition is P=30kN and q0=40 kN/m.
A wooden beam whose length is 1 m is 100 mm wide and 200 mm high. It carries a load of 100 kN as shown. Determine the total tensile stress at A. Select the correct response: 32.48 MPa 29.98 MPa 52.46 MPa 34.98 MPa 50 500 mm- 30° 150 KN
In the figure, find the length c of the overhangs so that the beam made of U profile can carry the loading safely. The safety stress (σç)emn=50N / mm2, (σb)emn=80N /mm2 for the tensile and compression condition of the material. The support range of the beam is L=6 m, cross-section dimensions a=210 mm, b=150 mm and wall thickness t=40 mm. The loading condition is P=30kN and q0=40 kN/m.
A concrete beam pre-stressed with a parabolic tendon is shown in the figure. The eccentricity of the tendon is measured from the centroid of the cross-section. The applied pre-stressing force at service condition is 1620 kN. The uniformly distributed load of 85 kN/m includes the self weight of beam. 85 kN/m 500 mm 750 mm 145 mm 6 m The net deflection at the mid-span of the beam will be [Grade of concrete used is M35]
2. A beam with an inverted U section is loaded as shown. What is the max flexural stress developed and the max beam shear developed in the beam? 30mm 30mm 2m 6m 2m 200m 250mm 40mm
A beam is simply supported on a span of 10 m. The beam supports a load of 15 kN/m on itsentire length and three 30 kN loads at its quarter points. A. If the maximum bending stress is equal to 250 MPa, determine the most economical W-shaped beam. B. Determine the actual maximum stress in the beam selected.
A simply supported beam supports a uniformly distributed load equal to 40 kN/m applied throughout the beam. What is the maximum flexural stress if the beam has a rectangular cross section with b = 300 mm and h= 500 mm? ( in MPa ) avoid truncation in the midle of solution ( 3 decimal places ).