A two stage steam turbine receives steam at 38 bar and 350°C. The expansion in the first turbine is carried out until the steam is just dry saturated. Before entering the second turbine the steam is reheated at constant,pressure to original temperature of 350°C. The steam expands in the LP turbine to a condenser pressure of 0.03 bar, Calculate, Work output in kJ/kg

A two stage steam turbine receives steam at 38 bar and 350°C. The expansion in the first turbine is carried out until the steam is just dry saturated. Before entering the second turbine the steam is reheated at constant,pressure to original temperature of 350°C. The steam expands in the LP turbine to a condenser pressure of 0.03 bar, Calculate, Work output in kJ/kg

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need help on the following question: The vapour compression cycle (picture provided), utilises the refrigerant R134a flowing at 0.05 kg s-1. Assuming that the compression is adiabatic and reversible. If the actual input power to the compressor is 2 kW, then: 1. You need to determine the theoretical input power to the compressor and the heat transfer (Φ) to theevaporator. Take the enthalpies h1, h2, and h3 to be 238.41, 263.68 and 81.5 kJ kg-1 (use the 'NH3 Refrigeration Table' where you can find online). 2. You need to determine the coefficient of performance based on your answer to the previous question (1). 3. You need to determine the compressors mechanical efficiency.
Steam engine with incomplete expansion receives saturated steam at 1.04 Mpa,expands it to 0.105 Mpa where release occurs. Exhaust is to a condenser at 40C.The actual engine uses 6070 kg/h of steam; it has a brake engine efficiency of 60%and a mechanical efficiency of 85%. The electric generator which it drives has anefficiency of 925. (a) For the ideal engine, find the thermal efficiency and the mep.For the actual engine, determine (b) the brake work in kW and the brake thermalefficiency, (c) the indicated work in kW, indicated thermal efficiency and indicatedsteam rate, (d) the combined thermal efficiency and the combined steam rate
The steam rate to a turbine for variable output is controlled by a throttle valve in the inlet line.Steam is supplied to the throttle valve at 1,700 kPa and 225°C. During a test run, the pressure atthe turbine inlet is 1000 kPa, the exhaust steam at 10 kPa has a quality of 0.95, the steam flowrate is 0.5 kg/s, and the power output of the turbine is 180kW. 1. What are the heat losses from the turbine? 2. What would be the power output if the steam supplied to the throttle valve were expandedisentropically to the final pressure?
In a marine gas turbine unit, a high-pressure stage turbine drives the compressor and a low-pressure stage turbine drives the propeller through suitable gearing. The overall pressure ratio is 4/1 and the maximum temperature is 650 o the isentropic efficiencies of the compressor, H. P. turbine, L. P. turbine are 0.8, 0.83 and 0.85 respectively and the mechanical efficiency of both shafts is 98 %. Sketch the process on the T-s diagram i. Calculate the pressure between turbine stages when the air intake conditions are 1.01 bar and 25 oC. ii. Calculate also the thermal efficiency and the shaft power when the mass flow is 60 kg/s. NB: Neglect kinetic energy changes and the pressure loss in combustion.
In a refrigerator the power rating impressed on the compressor is 1.2 kW. Thecirculating wire in evaporator is 5 kW and the cooling water took away 10 kW fromcondenser coil. The operating temperatures range is 18ºC and 0ºC and theircorresponding latent heats are 170 kJ/kg and 230 kJ/kg and the difference between theliquid energy is 35 kJ/kg. Find the actual COP of the system (2) relative COP, assumingthe vapour is just dry and saturated at the end of the compression.
1. The working substance for a Carnot cycle is 8 lb of air. The volume at the beginning of isothermal expansion is 9 ft3 and the pressure is 300 psia. The ratio of expansion during the addition of heat is 2 and the temperature of the cold body is 90°F. Calculate: a. QA b. V3
Steam is supplied to a two-stage turbine at 48 bar and 400 °C. It expands in the firstturbine until it is just dry saturated, then it is re-heated to 400 °C and expandedthroughthe second-stage turbine. The condenser pressure is 0.04 bar. Determine the specific work output of the system to 3 d.p? what is the specific entalphy in kJ/kg for state 2?
TH 3 kg of air as an ideal gas undergoes a Carnot refrigeration cycle as shown The isothermal expansion occurs at 300K and isothermal compression occurs at 600K. The heat transfer to air during isothermal expansion is 125 kJ. Pressure at the end of figure. isothermal expansion is 75 kPa. a. Find pressure at the beginning of the isothermal expansion. Show all work and explain your numbers. b. Sketch this cycle on the T-s diagram. Show on the diagram the system states (1,2,3, and 4), the cycle direction, and the cycle work (not its amount)
In an ammonia refrigerator , the pressure in the evaporator is 267. 58 KPa and theammonia at is 0.14 dry while at the exit is 0.86 dry . During compression the work done per kgof ammonia is 20 ,000 kg .m . Calculate volume of the vapor entering the compressor per minuteif the rate of ammonia circulation is 6.54 kg. The compressor has a volumetric efficiency of 90%and it runs at 150 rpm .The ratio of stroke to bore is 1 .Latent enthalpy of ammonia at basedon its evaporating pressure is 320 Kcal per kg and its latent specific volume of ammonia basedon its evaporating pressure is 0.436 m3 per kg .Specific volume of ammonia .A) 2.23 C) 2.46B) 3.23 D) 4.62
A reheater cycle is executed of 1 kg steam expanding initially from 12.547 Mpa and540.547 oC. The reheater pressures are 2.5547 Mpa and the steam leaves the reheaterat 420.547 oC. Condensation occurs at 0.02547 Mpa. Calculate W, ec and ee.
Steam enters the high-pressure turbine at 150bar and 550c and low pressure turbine at 40bar and 550c .the condensor pressure is 0.1bar using mollier diagram find 1.the dryness fraction at the end of low pressure turbine 2.efficieny 3.steam rate 4.heat rate 5.work ratio
Example 2: Refrigerant R-134a enter the compressor of a has a refrigerantor a superheared vapor at 0.14MPa and -10°C at arate of 0.05kg/sec and leave at 0.8Mp and 50°C.The refrigerant cooled in the condenser to 26°C and 0.72Mpa is throttled to 0.15MPa.Disregradingany heat transfere and pressure drop in the connecting line between the components. Determine: a) The rate of heat removed from the refrigerated space b) The power input to the compressor. c) Isentropic eff of the compressor d) COP of the refrigerantor.