A two branch duct system of circular duct is shown below. The fittings have the following equivalent lengthof straight duct upstream to branch 4m elbow 2m. There is negligible pressure loss in the straight throughsection of the branch. The designer slects 4pa/m as the pressure gradient in all sections. What diameter in ft should be selected in the 5m section? A. 0.54 B. 0.34 C. 1.12 D. 0.44

Q: 4- In the (Venturi-Meter Experiment) calculation the...volume/time. a-Re. b- Qactual d-Other…

A: Venturimeter is a device which is used for measuring the rate of flow through the pipe. Principle:…

Q: Problem # 3: Friction losses and volumetric discharge through a water piping system The cold-water…

A:

Q: d iron pipe system whose diameter is 0.75 inches and flow rate is 0.020 cfs. Do you agree with the…

A:

Q: Q = 8 cfs he= 25 ft D = ? =f=002, D=7966 in 0.42 For a certain project. a water discharge of 8 efs…

A: Water discharge (Q) = 8 ft2/sHead loss (hL) = 25 ftPipe length (L) = 100 ft

Q: The flow rate through 1 1/2 " pipe between B and C is: (a) 16 GPM (b) 10 GPM (c) 9 GPM…

A: The flow rate through 1 1/2 " pipe between B and C is equal to

Q: What is the pressure drop in psi of 60°F water flowing through 65 ft of horizontal 1-inch schedule…

A: Consider the solution below

Q: 1 QUESTION 1 Consider a desired pump operating condition which adds 35 psi at a flowrate of 500 gpm…

A: Given data  Flow rate = 500 gpm Pressure = 35 psi Density = 62 lbm/ft^3 Find the pump head

Q: A venturi meter has a main pipe diameter of 65 mm and 26 mm diameter of throat. When measuring the…

A:

Q: Design the rectangular duct system shown in figure below using equal friction method with frictional…

A: Given Data∆P=1Pa/mh=300mmQD=0.6m3/s=QF=QI=QJ

Q: Select the proper-sized steel tube for a flowrate of 25 gpm and an operating pressure of 1,000 psi.…

A: Basically, the flow rate is the speed at which fluid moves in a pipe, and the flow can be described…

Q: It requires a specific displacement before the flow become fully developed. Entry length a. depends…

A: In fluid mechanics, the hydrodynamic entry length boundary layer is a thin layer of a moving gas…

Q: 3) What are the flow Q and the velocity V when total head loss is H = 25 m? KENTRANCE = 1.0 KGLOBE…

A:

Q: Given a frictionless flow of water at 125.6 ft^s in a long, horizontal, conical pipe, of diameter 2…

A:

Q: For the hydraulic system of Figure, the following data are given: The pump is adding2.984kW to the…

A:

Q: What is the expected head loss per mile of a closed circular pipe with 17 in. inside diameter…

A:

Q: Problem : Taking into account only the local resistances, determine the level difference in the tank…

A:

Q: A fluid is flowing in a round pipe. The Reynolds number is Re = 3 x 10°. The relative roughness is =…

A:

Q: Calculate the pump capacity.

A: Suction line pipe diameter, ds=2 in=2*0.0254=0.0508 m                           1 in=0.0254 mSuction…

Q: The critical cavitation number of a pump is 0.12, the vapor pressure head is 0.2 m, the atmospheric…

A:

Q: Aspect ratio Supply temperature | Pressure drop per unit length | Main and branch đuct velocities…

A: An HVAC is a device used to produce cooling by dissipating heat in the form of fluid or refrigerant.…

Q: I need these three parts answered pertaining to the print provided. If you can not answer all three…

A: Part(a).From the given print,we can say that section A-A contains several parts.for example-It…

Q: 02: Size the supply circular duct system shown in figure below using equal friction method with…

A:

Q: otal head pressure 1 m2 and m2. n.

A: Write the expression of the head of the water flow from the nozzle.

Q: 2). Calculate friction heads when a flow rate of 1.5 m³/min circulate in two different pipelines.…

A: Given: The flow rate of water solution, Q = 1.5 m3/min The diameter of pipes, D2 = D1 = d = 2 in The…

Q: EL..20m K=0.5 A= fi= 0.02 D₁-0.3m Lis 150m F₂2 0.02 Da= 0.6m L₂=240m Valve For Valve K= 0.2 EL.: 5m…

A:

Q: Don't use chatgpt. I need right answer.

A: Given:Inner diameter of the hose (di) = 1 inThe inner radius of hose (ri) = di/2 = 1 in/2 = 0.5…

Q: A two branch duct system of circular duct is shown below. The fittings have the following equivalent…

A:

Q: a) The pressure head supplied by the pump, b) The total head loss between point b and 2.

A:

Q: Water flows into junction J from reservoirs A and Bthrough connecting pipes, the head loss through…

A: Given:Head loss in pipe A=10QA2Head loss in pipe B=4QB2water level at A=25.9 mwater level at B=18…

Q: (a) In a duct enlargement, the velocity reduces from 20 to 5 m/s. (i) If it is a 20°-angle gradual…

A: Givenv1=20m/sv2=5m/s Note-As per our company policy we are supposed to do only 1 Question if you…

Q: Air 20KP3 2 m Im 120 mm diam Water C-0.85 Water Figure 9.27 Problems 9.27, 9.28, and 9.61. A…

A:

Q: What water level H must be maintained in the tank as shown in Fig. P. 3.5.20 to deliver a flow rate…

A: To produce a flow rate of 5×10-4 m3/sec via the pipe, we must determine what water level H in the…

Q: a pipe reducer with the pressure at A and B is 345kPa and 290kPa. the diameter at A and B is 50mm…

A:

Q: What is Total Head of submersible pump

A:

Q: (Single pipe-determine pressure drop) Determine the pressure drop per 350-m length of a new…

A: Given:The length of the pipe is .The diameter of the pipe is .The average velocity is .

Q: Specifications: The total length of pipe in the three inch branch is 10 ft, and the length of pipe…

A: 1. a. 0.0146 cubm/sb. 0.0012 cubm/s2. 6.67 m3. R = 26806Explanation:Since the pipe having Heat…

Q: The coefficient of friction for a flow through pipe with Reynold’s number 40000 is a. Need density,…

A:

Q: Q3) What is the maximum permissible difference in elevation between the water surface of an intake…

A: As we know the NPSH means the net positive suction head. it measures the pressure in the fluid by…

Q: 4. Find total loss in the problem Where: Q = 10 litre / second, 1= 0.33 and k for both bends and…

A:

Hydronics