A turbine-based steam engine consists of a tank, regulator and turbine. The tank with a volume of 100 liters, first contains a saturated liquid at a pressure of [.100] kPa. The tank is heated and the pressure begins to build up to a pressure of], 700 [kPa. Saturated steam spreads th rough the turbin e and out into the environment At a pressure of [100] kPa without changing quality. The heating stops when the liquid in the tank runs out. Calculate the tu rbine work. And cal culate the heat transfer to the con tainer W = kJ 5419 Q= kJ 154 410 W Sat. H,O Turb.

A turbine-based steam engine consists of a tank, regulator and turbine. The tank with a volume of 100 liters, first contains a saturated liquid at a pressure of [.100] kPa. The tank is heated and the pressure begins to build up to a pressure of], 700 [kPa. Saturated steam spreads th rough the turbin e and out into the environment At a pressure of [100] kPa without changing quality. The heating stops when the liquid in the tank runs out. Calculate the tu rbine work. And cal culate the heat transfer to the con tainer W = kJ 5419 Q= kJ 154 410 W Sat. H,O Turb.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Show detailed solution please.
Q2: A piston-cylinder system contains 1 kg of air at (V1, P1, T1). The air is heated at constant pressure process until the volume is doubled. Then the air is compressed according to the low (PV=C) until the piston regains its original position. Then the air is cooled at constant volume processes until the pressure reach to the original value. Assume (V1, P1), Draw the cycle on p-v diagram and calculate 1- Net work done 2- Net heat
A compressor plant compresses 10 m of free air every minute to 10 bar gauge with a thermodynamic efficiency of 70 % in single stage. a) Calculate the power required for this process if it were done ideally. b) Caculate the power used by the real plant. c) What value has the polytropic index have taken during the real compression ?
Note: Show all your solutions in separate sheets as required. Indicate all of your answers on this page in the provided blank lines. 1. Using the Steam Tables, find and entropy of steam at the inlet and outlet of a boiler and heat added when subcooled water at pressure = 5 Mpaa (subcooled by 64 deg C measured at boiler inlet), is superheated to 100 deg C SH at the same pressure. Total flow volume rate of steam = 0.5 cu.m per sec. Indicate units.
Q40. a)What mechanical forces are generated in a reciprocating compressor? b) Briefly explain them.
IN A THROTTLING VALVE, steam of P = 1000 kPa H = 1000kJ/kg flows until P becomes 100kPa. What is the fraction of the liquid that was vaporized? a.0.118 b.0.189 c.0.159 d.0.140 e.0.258
Steam enter a turbine with an enthalpy of 1292 Btu/lb anf leaves with an enthalpy of 1098 Btu/lb. The transferred heat is 13 BTU/lb. What is the work in BTU/min an in h for a flow of 2 Ib/sec?
The power generated by an adiabatic steam turbine is 5MW, when the steam enters the turbine at a pressure of 2.3MPa, a temperature of 400C and a speed of 50m/s; and leaves the turbine at a pressure of 15kPa, a quality of 90% and a speed of 180 m/s a) Represent the process on a P-V diagram. b) Find the mass flow rate of the steam. c) Find the exit area of the turbine.
3. We have steam at 10 bar flowing in a line. We open a valve attached to the line and the steam comes out to 1 bar at 100 C. a) is this possible? b) What is the state of the steam in the line ...compressed liquid, saturated mix, superheated vapor?
Thermodynamics Please clear writing! Take your time all I want is the correct answer
Determine the amount of work required to compressed 1.5 kg of air at a pressure of 7 barg. The isentropic index is 1.2 and the air intake is at 1 bar, 20C & RH =65%. i) Find the temperature at the end of the compression. ii) Represent the above process on a p‐v diagram. iii) If the isentropic efficiency is 65%, find the indicated or real work. iv) Find the shaft work needed if the mechanical efficiency is 75%.
Provide a complete solution and answer for the given problem in the attached image.