A truss with three members rests on a surface and is loaded from the top by P. Assume the contact between the structure and the floor is frictionless. Also, assume the pinned joints in the truss are frictionless and the bars in the truss have negligible mass. A B. L, D (a) Draw the free body diagram for each of the three members in the truss (AB, CE, and CD). (b) Find the force in member AB.

Q: What is this called?

A: Chisel

Q: Determine the Centroid of 3 Areas.

A:

Q: 5. Find diameter y. All dimensions are in millimeters. 1 + 19.30 DIA 118.00 -३०

A: Tapered beam with larger diameter at AB = 19.3 mm  Length of beam ,L = 118 mm  Tapered angle = 3°…

Q: Determine number of external indeterminacy

A: Given data : Number of external support reaction (R)=3+3=6 m=Number of member connected at hinge…

Q: 10 + 5x < 6+3x

A:

Q: Determine the ỹ coordinate. y b. = ky? a

A:

Q: FIHD THe CENTROID (x $ Y) of THe GazOMETRY

A: Centroid is the point where the mass of whole body acts. If there is a figure which consists of…

Q: Fo B - P 800 mm C -600 mm

A:

Q: 7⁄8 inch+  5⁄32 inch

A:

Q: Describe briefly the T-v Diagram.

A: The TV diagram refers to the Temperature-Volume diagram for a particular substance. The diagram…

Q: What is (-3,0) scale to 1/3

A: Given: coordinates (-3,0) scale = 1/3 To find convert the coordinates to the given scale.

Q: Determine y for the area shown y 1" 1" in .5" 1" 2" 2" X

A:

Q: what is the difference between 42 square meter and 42 meter square

A: It is needed to differenciate between 42 square meter and 42 meter square.

Q: According to this figure, What is d? What is dt?

A: Draw the figure.

Q: what are the USCS group name for each of the four gradations

A: Given: Specimen LL PL PI Cc Cu 1 53 24 29     2       1.05 95.52 3 27 16 11 3.06 28.34 4…

Q: BEAUTIFUL 01/ Construct Polynomial Forth function gases in cas, within [0, 1]ns4

A:

Q: Determine degree of total indeterminacy

A: Given data : The given structure is truss structure . It is pin connected carrying tension or…

Q: continue the last part

A: Data for pump performance curve is given. We need to select which pump combination would work for…

Q: Is sigma xy horizontal and sigma xz vertical

A: Reference: wikimedia commons

Q: 9- The Scale The scale of a drawing is... Lo = X Lo = Lo= e= If e 1: Full size representation. e 1:…

A:

Q: wrong given, pls. answer

A: Given: Span= 10m, axle loads as shown in figure

Q: * Dount command Creates a filled circle or a filled ring O a filled circle or a wide ring. a wide…

A:

Q: 1) Determine the area of the shape below. -130.0- 100.0 -160.0-

A: The above figure is the trapezoid  The area of the trapezoid = sum of the parallel…

Q: Explain any fiften (15) AUTOCAD commands used in drawing

A: Autocad is a computer based drawing software which is in the field of civil engineering to prepare…

Q: For the following items, answer whether the multiview projection matches the isometric drawing depic…

A: The given figure shows the different items, it is required to state whether the Multiview projection…

Q: why 3.5 instead of 2.5?

A: Correct solution is provided below

Q: Differentiate initial and boundary value problems.

A: Both type of problems are similar to each other except for that boundary value problem have…

Q: PROBLEM 2: Determine Ix and Tx.

A: given- a plane figure to find- M.O.I  about X-axis and centroidal axis.

Q: Locate the centroid y̅ of the area.

A: Draw the figure. From the figure, dA = y dx

Q: [Choose ] solve equilibrium equations simultaneously ensure you have an equal number of unknowns and…

A: Understand force flow. Understand the math behind structural analysis (concepts like virtual work…

Q: Difference betwen Veletile nd frzcead Saled

A:

Q: 38 O 18 22 66 102 The known: front projection, side projection Required: Draw the three projections…

A:

Q: The column section shown above is reinforced with equal number of 20 mm bars с 1. on each face.…

A: Answer  1) Calculation of neutral axis 'c' We know that at balanced condition strain at extreme…

Types of Composite

Composite materials are formed by merging two components that have different chemical and physical properties. The merged output is termed as a composite, whose properties are completely different from the individual components. Composite materials also have better strength than the individual components.Composite materials usually have two main parts, reinforcement material, and matrix material. The matrix material acts as a binder and surrounds the fiber of another material that bears a much higher strength. This material is known as the reinforcement material. The matrix materials are usually high-strength additives resins, while the fibers of the reinforced material can be random, oriented, and in a mat format.Composite materials are also known as fiber-reinforced composite polymers because they are composed of the polymer matrix which is reinforced to laboratory-created fibers or naturally occurring fibers, such as glass fibers, carbon fibers, or aramid fibers. Under the application of external loads, the matrix material absorbs and transfers the loads to the fibers, these fibers in return provide good compressive strength, tensile strength, and stiffness to the fiber-reinforced composite materials.Depending upon the matrix and the reinforcement material, different properties can be induced to the fiber-reinforced composite materials, including good corrosion resistance properties. The most common matrix material is the resin while the glass fibers act as the reinforcement material. Strong fibers provide strength and stiffness to the composite materials while, a soft and flexible resin provides shape to the composite materials.