A triangular beam having a base width of 433 mm has a total depth of 776 mm. It is reinforced with 5- 16mm bars placed at 70mm (steel cover) above the bottom of the beam. f'c=24.06 MPa, fy=275 MPa. Use fc (allow) = 0.45f'c and fs(allow) %3D = 0.5fy %3D Calculate the capacity of the beam in kN-m using WSD.

A triangular beam having a base width of 433 mm has a total depth of 776 mm. It is reinforced with 5- 16mm bars placed at 70mm (steel cover) above the bottom of the beam. f'c=24.06 MPa, fy=275 MPa. Use fc (allow) = 0.45f'c and fs(allow) %3D = 0.5fy %3D Calculate the capacity of the beam in kN-m using WSD.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the design moment capacity of the beam with given properties below. bf = 550mm bw 350mm tf = 100mm %3D d = 370mm %3D d' = 100mm %3D fc' = 34.5 MPa fy = 400 MPa %3D As = 6-32mm bars a USE NSCP 2001, Mu = kN-m b. USE NSCP 2015, Mu = kN-m
AW 12 x 65 column section shown in the figure is pinned at each end and has an additional support in the weak direction at a point 4.1 m from the top. Use X- 4.8 m K 1 for both directions. X+Y Properties of W 12 x 65 A 12323 mm2 - 134.11 mm ry 76.71 mm Fy- 248 MPa Determine the allowable compressive strength (kN).
Determine the force of the members for the space truss shown in the figure. Joints A and B are supported by ball-and-socket while Joint C is supported by short link along z-axis. Indicate whether member is tension (T) or compression (C). 2m y Sm Az By BX Bz PAR Ax CSXScanned with Ca canner a SISU KN 15m 1 2117
2. A vertical member of a steel truss is subjected to a live load of 25 kN and a service dead load of 50 KN. The flat bar is welded to the guzzette plate with sufficient weld length such that the reduction factor "U" is equal to 1.0. Determine if a 10mm x 100mm plate is safe to carry the load. Given: Ag = 1000 sq mm width = 100mm thickness = 10 mm U = 1.0
Design the reinforcements of the given T beam below. bf=800mm bw=450mm tf=120mm d=600mm d'=80mm fc'=35MPa fy=350MPa USE NSCP 2015 A.Mu = 1300kN-m, As = B.Mu = 1600kN-m, As = mm2 _mm2, As' = mm2
3. Determine maximum strength P for the bracket connection in the figure. ST37 steel is used for the connection, F = 2400kg /cm,F, = 3700kg /cm %3D %3D IPE200 15 cm P=? PL 250x150x15 mm te 7 mm, L=250 mm
Q2:If allowable stresses are ot = 165MPa, oc=100MPa t = 70MPa determine max. value of W. W 150mm 50mm 2m 8m 2m 150mm
I need a clear answer by hand, not by keyboard and fast answer within 20 minutes. Thank you | dybala For the beam loaded as shown, find the maximum tensile and compressive bending stresses and maximum shearing stress.. IN.A=4*10mm* 80mm 100mm 60mm 60mm 1.5KN 2kN/m 1mal A |-----|- | Im ++ Im->> 3m 3kN/m
HiW@ Draw S.f.n and BiMin for beam shown by Naphial methds Anst hinge %3D M= 9 W.m 3m 2m 3m Mmny = -6 IW.m
A wide flange section has the following properties. A- 6645 mm? bị = 152.40 mm ty - 10.80 mm d- 449.58 mm tw - 7.62 mm Fy - 250 MPa Compute the plastic section modulus about the major principal axis. (x 10° mm)
أ.د. رمضان المبروك A PL170mm x 10mm tension member is welded to a gusset plate as shown in Figure below. The steel is A36. Assume that Ae = Ag and compute the following. %3D fy = 250 MPa & f, = 400 MPa %3D %3D PL 170mmx10mm a. The design strength for LRFD. . The allowable strength for ASD. roblem (4):
EQuiz No.3 584nkkz1 Cc7KLzOsdr9YUFgvcfFSqpsdlyljtewQ/formResponse Choose the correct answer What will be the value of load applied parallel to the diagonal of (100x100x100))mm cube since the splitting tensile strength=3 Mpa 57.8 KN O 46.7 KN O 47.1 KN O (28)=27.5 Mpa, then the fc(180)=-- for concrete produced using moist