A time-varying signal E; is applied to the (-) input terminal and ground to the (+) input terminal of an op-amp LM741. Sketch accurately: (a) Vo vs t (b) Vo vs E; Circle the right answer: The circuit is: (a) An inverting zero-crossing detector (b) A non- inverting zero-crossing detector +15 V AA- E, vs. t +3 E, LM741 (ms) 8 10 k2 Vo - 15 V

A time-varying signal E; is applied to the (-) input terminal and ground to the (+) input terminal of an op-amp LM741. Sketch accurately: (a) Vo vs t (b) Vo vs E; Circle the right answer: The circuit is: (a) An inverting zero-crossing detector (b) A non- inverting zero-crossing detector +15 V AA- E, vs. t +3 E, LM741 (ms) 8 10 k2 Vo - 15 V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1- Mention any two advantages of Integrated Circuit . 2- For the circuit given below : Vin is a sine wave Vinpp=6 V and Vref=-2.4 V , Assume Vsat=±12V Name the circuit and draw the input and output waveforms . Vin Vref 3- Explain why open-loop op-amp configurations are not used in linear applications? Draw the block diagram of opamp and define the function of each block
I want the answer with details as soon as possible. Please Q-Design an op-amp circuit to amplify the AC voltage of 0.7v to become 3v , And the voltage of VCC is 5v DC.
If the ideal design for op-Amp circuit generate 200 mV at the output, Then practically with 26 mV offset voltage the output voltage of the circuit will be equal to .. . mV
Sketch the output voltage waveform for each op amp circuits given
Find an expression for the output voltage v, below. Assume an ideal op-amp. What mathematical operation does the circuit perform? R2 R
2. Design an op-amp circuit for cach of the following applications. Write the name of the circuit, draw the circuit diagram, and determine specific numerical values for the circuit elements. a) An accelerometer outputs voltages between -17 mV and +17 mV. We need the input to our microcontroller to range from -5 V to 5 V, where sign does not matter but the maximum amplitude corresponds to the maximum accelerometer output.
H: Design OP-Amp eircwt that Poduce an out Put an given by Uo = - ( 4 V,t Uz to.l U3) If u, = 2 sinwt = 5 V and U3 = - 100V sketch the ont Put vo ltage waveform ?
1) Op-amp limiting factors - Current Saturation U2 Vin R1 OUT OPAMP R2 RLoad The saturation output current for the above op-amp is +/- 15mA. For the following input signals, determine if the output appears as would be expected in an ideal circuit. Include sketches of the output voltage. a) R1 = 100, R2 = 900, an open circuit load, and Vin is 2Vpp triangle wave with zero offset voltage (Vmax 1V, Vmin = -1V) and a period of 2ms. b) R1 = 100, R2 = 900, a 1k load, and Vin is 2Vpp triangle wave with a 1V offset voltage (Vmax=2V, Vmin = 0V) and a period of 2ms. c) R1 = 100, R2 = 900, an open circuit load, and Vin is 4Vpp triangle wave with zero offset voltage (Vmax=2V, Vmin = -2V) and a period of 2ms.
One way to measure the slew-rate limitation of an op amp is to apply a sine wave (or square wave) as the input to an amplifier and then increase the frequency until the output waveform becomes triangular. Suppose that a 1-MHz input signal produces a triangular output waveform having a peak-to-peak amplitude of 4 V. Determine the slew rate of the op amp.
1- Mention any two non linear applications of op- amp. 2- For the circuit given below : Vin is a sine wave Vinpp=9 V and Vref=2.4 V , Assume Vsat=±12V Name the circuit and draw the input and output waveforms . Vo Vin Vref 3- Explain why open-loop op-amp configurations are not used in linear applications? Draw the block diagram of opamp and define the function of each block
Electrical Engineering With an op amp design a square wave oscillator at ± 3 volts with a frequency at 20 kHz. Draw the schematic of the square wave oscillator. Write the formulas that is using for the design and the values of the resistors and capacitors that are needed to get the requested frequency.
11. The output of a particular Op-amp increases 8V in 12µs. The slew rate is .......