With an op amp design a square wave oscillator at ± 3 volts with a frequency at 20 kHz. Draw the schematic of the square wave oscillator. Write the formulas that is using for the design and the values of the resistors and capacitors that are needed to get the requested frequency.

With an op amp design a square wave oscillator at ± 3 volts with a frequency at 20 kHz. Draw the schematic of the square wave oscillator. Write the formulas that is using for the design and the values of the resistors and capacitors that are needed to get the requested frequency.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

How can I add two voltages values together with on op amp? Using op amps, how to make an AD Converter? A DA Converter? What components determine the frequency of an astable, 555 oscillator? Draw the circuit. Draw a circuit for both an astable and a monostable, 555 multivibrator. What is the duty cycle and percentage duty cycle of a pulse train or square wave? What is the overshoot, rise time, fall time, and pulse width of a pulse and where on the waveform is each measured?
Given the four statements, which of the following statements are true about an op-amp integrator? i. For an op-amp integrator with R = 100KOhms, C waveform, the output waveform is a cosine waveform. 10UF and a sine wave input %3D ii. For an op-amp integrator with R = 100KOhms, C waveform, thc output waveform is a squarc wave. 10UF and a triangular input %3D %3! iii. For an op-amp integrator with R = 100KOhms, C waveform, the output waveform is a sawtooth waveform. = 10UF and a sine wave input %3D iv. For an op-amp integrator with R 100KOhms, C 10uF and a square wave input waveform, the output waveform is a triangular waveform. Oi, ii, i O i, ii, iv O i iv O ii, ii
In a Wien bridge oscillator circuit, resistor and capacitor form a series branch and a parallel branch. The value of the resistor is 200 ohm and the value of the capacitor is 10 mF. Determine the frequency of oscillation for the Wien Bridge oscillator circuit.
G) build a low-frequency square wave generator using a basic comparator having a frequency of 1kHz and a 30% duty cycle. Explain the principle of operation and the type of feedback of the op-amp. What is the advantage of this circuit? H) Build a phase-shift oscillator using, C=1µF and +10V power supply to produce a 10 kHz sinusoidal waveform. Generate your plots and compare output results. Highlight any discrepancies and discuss what happens if we want to increase the frequency to 100 kHz. I) Build a Colpitts oscillator producing 100kHz Discuss its advantage over RC oscillators. How can you modify the circuit to include a crystal in your circuit? What is a typical application of such an oscillator? Discuss the advantages and disadvantages of crystal oscillators.
1- Mention any two advantages of Integrated Circuit . 2- For the circuit given below : Vin is a sine wave Vinpp=6 V and Vref=-2.4 V , Assume Vsat=±12V Name the circuit and draw the input and output waveforms . Vin Vref 3- Explain why open-loop op-amp configurations are not used in linear applications? Draw the block diagram of opamp and define the function of each block
if you design differentiator to differentiate input signal varies in frequency between 1 KHz and 20 KHz then find. Cutoff frequency=.......... 01000 O2000 03000 O4000
Boost Converter Design A boost converter is required to have an output voltage of 8 V and supply a load current of 1 A. The input voltage varies from 2.7 to 4.2 V. A control circuit adjusts the duty ratio to keep the output voltage constant. Select the switching frequency. Determine a value for the inductor such that the variation in inductor current is no more than 40 percent of the average inductor current for all operating conditions. Determine a value of an ideal capacitor such that the output voltage ripple is no more than 2 percent. Determine the maximum capacitor equivalent series resistance for a 2 percent ripple.
An op-amp comparator in a firing circuit can produce waveforms at the output of up to 20 V peak-to-peak without any distortion. An inverse cosine-based firing circuit with a voltage range from +10 to -10 (reference voltage) is used to produce a gating signal for the SCR at the desired delay angle. if the reference voltage is -5.01 volts, the delay angle (in degrees) would be: O A. None of the other choices are correct O B. 150 O C. -120 O D. 120 O E. 60
Q2. Find Q-point when VBB = 1V, 2 V and 3 V.. Assume VCE(sat) = 0 V. Re 1.0 KO Vcc RB www Bpc = 50 20 kN Draw the output waveform for the circuit shown below
6. An AC precision integrator is desired for a particular application to perform the operation: Vo'(t) = -1200 Vi(t) dt The primes indicate the ac portions of the respective functions. The lowest frequency other than a possible de component of the input signal is estimated to be 1.5 kHz. Determine a suitable design. 7. A low frequency differentiator is desired for a particular application n to perform the operation Vo(t) = -0.002 dvi(t)/ dt Based on a periodic signal with a frequency of 1 kHz, determine a suitable design. 8. Design an astable 555 timer circuit to produce 1kHz square wave, where TH = 0.35 ms and T₁ = 0.65 ms. Select C = 0.01 UE, Determine R₁ and Ra. 9. Design a monostable 555 timer circuit to produce an output pulse 5 ms wide. 10. Using op amps with Xsat = +/- 13 V, design a square/ triangular wave function generator circuit to generate 2 kHz triangular wave with a peak-to-peak voltage of 12 V. 11. Design a non inverting Schmitt trigger circuit with VT to be adjustable…
An op-amp comparator in a firing circuit can produce waveforms at the output of up to 28 V peak-to-peak without any distortion. An inverse cosine-based firing circuit with a voltage range from +14 to -14 (reference voltage) is used to produce a gating signal for the SCR at the desired delay angle. if the reference voltage is 5.92 volts, the delay angle (in degrees) would be: O A. -155 O B. None of the other choices are correct O C. 155 O D.-25 O E. 65
A boost converter is required to have an output voltage of 8 V and supply a load current of 1 A. The input voltage varies from 2.7 to 4.2 V. A control circuit adjusts the duty ratio to keep the output voltage constant. Select the switching frequency. Determine a value for the inductor such that the variation in inductor current is no more than 40 percent of the average inductor current for all operating conditions. Determine a value of an ideal capacitor such that the output voltage ripple is no more than 2 percent. Determine the maximum capacitor equivalent series resistance for a 2 percent ripple.