A three phase inverter has a Y- load. The inverter connected frequency is fo= 60 Hz and the DC input voltage Vi = 220V. The applied control signal is a 120 deg conduction mode. The RMS magnitude of the fundamental VL1 is equal to 171.53V, then the distortion factor (DF) is equal to: Select one: a. 8% b. None of these c. 1.21% d. 0.85%

A three phase inverter has a Y- load. The inverter connected frequency is fo= 60 Hz and the DC input voltage Vi = 220V. The applied control signal is a 120 deg conduction mode. The RMS magnitude of the fundamental VL1 is equal to 171.53V, then the distortion factor (DF) is equal to: Select one: a. 8% b. None of these c. 1.21% d. 0.85%

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Single-phase Half Wave Inverter produced a Square wave output across the load R=3 ohm and E=11OV and duty cycle d=40% 1- plot the wave form of output voltage , voltage across switches, and the source current 2- find the average load current 3-the power delivered at the load
A modified square wave DC-AC inverter is designed using an H-bridge. The output waveform voltage is illustrated below with = 20.0° a. Determine the RMS (effective) voltage of the waveform. b. Determine the THD of the resulting voltage wave form. 200 -200 Vo, [V] e 180° 360° 540°
3. A single-phase to single-phase cycloconverter "bridge type" with input voltage and frequency 150V and 50Hz. respectively. The output frequency is 10Hz and the firing angle equal to 45°. The load is resistance with the value of 1002 in series with reactive inductance of the value of 20mH. Assume the extinction angle equal 180°. a. Draw the waveforms output voltage, output current, source current, the thyristors currents (iT, IT, IT and in) b. Calculate the rms of output voltage. c. The rms current of each thyristor. d. The input power factor
Devices that pass the signal from its source to the measurement device without aphysical connection by using transformer, optical or capacitive coupling technique arecalled?Select one a. bridgesb. isolatorsc.filters d.rectifiers
a type of DC source where the characteristic output voltage has perfect unidirectional waveform and is based on electrochemical principle. A. Gemerator B. Converter C. Battery D. Inverter
Square wave inverter to a 125 V dc source,It has an output frequency of 60 Hz and R=20Ω and L=25 mHit has an RL series Load with.a. Calculate load current. b. Calculate RMS load current. c. Determine the average welding current.
How you can obtain a single phase inverter with quasi square wave output voltage if you have only single phase inverters with square wave output voltage
A single phase half-bridge voltage source inverter (VSI) has a resistive load of 2.4Ω andinput dc voltage Vdc = 48V. The desired fundamental frequency of the load voltage is 50 Hz.Determine: RMS output voltage at fundamental frequency and voltage rating of switches
A Capacitor filter is used at the output across the load in order to minimize the ripple factor of the output voltage. The expressions of the average output voltage Vpc and the output AC component VAc are given below. If R = 1k2 and the single phase bridge rectifier supplied from a 120V - 50 Hz sinusoidal source, then the capacitor value that will maintain the amount of the output ripples to less than 4% would be equal to: VDC = Vm(4FRC – 1)/4ƒRC) VAC = Vm/(4/2ƒRC) Select one: O a. 63.39uF O b. 33.2uF O c. 93.39UF O d. 126.2uF TOSHIBA
For the figure below, Find the open circuit voltage VTH and the short circuit current IN across the terminal. show the steps.
A single phase inverter has square wave output voltage. What is the percentage of the fifth harmonic component in relation to the fundamental component ?
In an inverter circuit, the voltage value is equal to the input voltage value and the output voltage value. a.VIL b.VOL c.Vth d.VIH