A thin rectangular polymer plate PQRS of width b = 361 mmand height a = 193 mm is shown in the figure. The plate is deformed so that corner Q is displaced upward by c = 3.1 mm and corner R is displaced leftward by the same amount. Determine the shear strain at corner P after deformation. a y = b S a urad

A thin rectangular polymer plate PQRS of width b = 361 mmand height a = 193 mm is shown in the figure. The plate is deformed so that corner Q is displaced upward by c = 3.1 mm and corner R is displaced leftward by the same amount. Determine the shear strain at corner P after deformation. a y = b S a urad

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A thin polymer plate PQR is deformed so that corner Q is displaced downward 0.9 mm to new position Q', as shown in. Determine the shear strain at Q' associated with the two edges (PQ and QR). Assume a = 150 mm, b = 216 mm, c = 180 mm, and A = 0.9 mm. a b P R C Answer: Shear strain y = Q i A X urad.
AN ALUMINUM TUBE IS FASTENED BETWEEN A STEEL ROD AND BRONZE ROD AS SHOWN IN THE FIGURE. AXIAL LOADS ARE APPLIED AT THE POSITIONS INDICATED. FIND THE VALUE OF P THAT WILL NOT EXCEED A MAXIMUM OVERALL DEFORMATION OF 5mm OR A STRESS IN THE STEEL OF 120MPa, IN BRONZE OF 130 MPa AND IN ALUMINUM OF 90 MPa. Modulus of Elasticty of Bronze = 80 GPa, Aluminum = 65 GPa and Steel = 210 GPa. 2P P 3P 4P L = 500mm 800 A = 400mm² 900 600 700 C
A thin polymer plate PQR is deformed so that corner Q is displaced downward 1.3 mm to new position Q', as shown in. Determine the shear strain at Q' associated with the two edges (PQ and QR). Assume a = 64 mm, b = 100 mm, c = 80 mm, and Δ = 1.3 mm.
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 20 x 103 mm while those at CD decrease 60 x 103 mm in the 230- mm-gage length. Using E = 180 GPa, determine the flexural stress at the top fiber. Answer must be in MPa. Given: a = 40 mm, b = 130 mm, and c= 70 mm. gage length a mm A B. b mm c mm
The specimen shown is made from a 25 mm diameter cylindrical steel rod with two 38 mm outer-diameter sleeves bonded to the rod as shown. Knowing that E = 200 GPa, determine (a) the load P so that the total deformation is 0.05 mm, (b) the corresponding deformation of the central portion BC. 38 mm diameter P' 25 mm diameter B 38 mm diameter C 50 mm 75 mm 50 mm
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 50 x 10 mm while those at CD decrease 60 x 10 mm in the 220-mm-gage length. Using E = 190 GPa, determine the flexural stress at the bottom fiber. Answer must be in MPa. Given: a = 60 mm, b 120 mm, and c = 80 mm. %3D gage length a mm A B b mm D. c mm
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 30 x 10-3 mm while those at CD decrease 70 x 10 mm in the 270- -3 mm-gage length. Using E 180 GPa, determine the flexural stress at the bottom fiber. Answer must be in MPa. Given: a 50 mm, b = 120 mm, and c = 70 mm. gage length A a mm B b mm D. C. c mm
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 40 x 10* mm while those at CD decrease 90 x 10 3 mm in the 240-mm-gage length. Using E = 120 GPa, determine the flexural stress at the bottom fiber. Answer must be in MPa. Given: a 50 mm, b = 130 mm, and c 80 mnm. gage length a mm b mm c mm Next>
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 40 x 103 mm while those at CD decrease 80 x 10 ³ mm in the 230-mm-gage length. Using E = 150 GPa, determine the flexural stress at the bottom fiber. Answer must be in MPa. Given: a = 40 mm, b 130 mm, and c = 90 mm. gage length a mm b mml c mm
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are mm while those at CD decrease 70 x 10 mm in the 260- -3 found to increase 30 x 10 -3 mm-gage length. Using E = 150 GPa, determine the flexural stress at the bottom fiber. 40mm, b Answer must be in MPa. Given: a = = 110 mm, andc= 80 mm. gage length a mm b b mm c mm 8.
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 20 x 10 mm while those at CD decrease 60 x 10 mm in the 250-mm-gage length. Using E= 150 GPa, determine the flexural stress at the bottom fiber. Answer must be in MPa, Given: a = 60 mm, b = 120 mm, and c = 80 mm. gage length a mm b mm Library entation c mm Survey DENTS TION
Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.58 in. and an elastic modulus of 2430 ksi. Bar (2) has a cross-sectional area of 0.714 in and an elastic modulus of 4110 ksi. Assume Ly-18 in., Lz-47in, Q=6,4 kips, P-3.2 kips, and R-128 kips. Determine the horizontal deflection of end Crelative to end A. (1) Answer: uCA in.