3. A cylinder with one closed end and one free end has an outer radius, b =260mm, and an inner radiu a = 55mm. Determine maximum tangential, radial, shearing, and longitudinal stresses for an internal pressure of pi = 55 MPa.

Q: This still doesnt answer how to get points 2,  2', and 1', so how did you get it?

A: Itis asked to explain how the state points 2, 2' and 1' are obtained

Q: v) w) What is the distance, dsy, of shape 5's centroid from axis Yo? What is the distance, dzy, of…

A: (v) Consider the shape 5 and calculate the distance, d5y, of shape 5's  centroid from axis y0.

Q: Write short notes on significance of grashoff number.

A: The answer is given below

Q: 2. Draw the sketch of 'Drilling machine' and explain any four parts. Use pencil to draw the neat…

A:

Q: 2. Write 5 details found on the drawing title block?

A: The bottom right hand corner block in engineering drawing sheet is known as title block. This block…

Q: I keep being told this requires me to make my own drawing, but that is incorrect. The instructions…

A:

Q: I have three parts that I need answered pertaining to the print provided below.   Do the dimensions…

A: It is mentioned in the drawing specification that “dimensions and tolerances apply before the…

Q: 8. A note in the comment section of a title block mentions that all faces should have a +.10…

A: Circularity (roundness) tolerance is 2-D in nature.

Q: Q3: Mark the Following True or False 1. Hidden lines are used in sectioned area when they are needed…

A: 1.TRUE 2. TRUE 3.TRUE 4.FALSE 5. FALSE 6.FALSE 7.TRUE 8.FALSE 9.FALSE 10.FALSE 11.TRUE 12.TRUE…

Q: A particle P of mass m = 3 kg arrives at point O with a horizontal velocity and starts rolling down…

A: Given:

Q: Given the Top View, Right View, and the outline of the Front View. Create a section view based on…

A:

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: Draw the top view  front view  right side view  on graphing paper please. Put measurents if…

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Discuss how the Cylindrical Square is used.

A: A cylinder square is used for checking the squareness of vertical axis with reference to horizontal…

Q: 3. What makes EDM become a key in tool and die making machine tool ?

A: The main reason of using EDM in die making process are:-

Q: can you please write it in a proper way?

A:

Q: Develop two possible hierarchies for assembling a model from the parts given below: Top Pins…

A: Given question: Develop two possible hierarchies for assembling a model from the parts given below:…

Q: With reference to the drawing callout in figure 5 below, which part(s) would 'pass' or 'fail' along…

A: Data given-  Dimensions of standard size  0.25±0.01 So tolerance is equal to 0.02  And the upper…

Q: 1.00 1.38 3.38 38 2.00

A: Select the correct statement about the notation circled in green and marked as letter D. Assume all…

Q: Write TRUE is the statement/s is True. If the statement is false, identify the word/s that makes the…

A: The chip compression ratio can be defined as the ratio of the chip thickness and uncut chip…

Q: what is the scale if a line is 10 inches but is  drawn 5 inches long.

A: Finding scale if a line is 10 inches but is  drawn 5 inches long.

Q: short notes on any two types of chips formed during metal cutting operation

A: Metal cutting is defined as "the act of eliminating undesirable material from a block of metal in…

Q: of the table) and free to move if a force is applied. A force is applied on it as the arrow…

A:

Q: 1. Given the following measurements (in metric and English respectively) of a metal cylinder: length…

A: as you mentioned I solved 1st. one. For solution refer below images.

Q: In the context of our teaching and learning, which one of the below statements is mostly correct…

A: The correct option is second.

Q: A piece of 12-gauge sheet metal is 7⁄64 inch thick. A stack of sheet metal is171⁄2 inches thick. How…

A: Given12 guage sheet metal sheet thickness t=7/64 inchthickness of stacked sheets t2=171 2inches

Q: What is the key information that needs to be incuded in a section view on an assembly drawing.…

A: The Answer is below

Q: Can you show the work but written out please so I can see the steps better.

A:

Q: 1. How is fraction changed to decimal? A. Divide the denominator by the numerator B. Divide the…

A: Since we answer only one question at a time, we will answer the first one. Please resubmit the…

Q: the isometric drawing has to be in 30 degree angle or vertical

A: It is asked to describe whether the isometric drawing has to be at 30 degree angle or vertical

Q: I need these two parts answered (Multiple Choice). If you can not answer all two parts please leave…

A: Problem 1To determine the tolerance specified for the depth of groove in the enlarged view, refer to…

Q: The impact test is used to find a material's it's ability to absorb energy before it fractures. O.…

A: About impact test. Impact test is used to determine the dynamic toughness material. In this test a…

Q: Part C - Maximum allowable axial force for fixed-and-free-end support If the cylindrical column is…

A:

Q: Indicate whether the terms are like or unlike. - 322, 5z? ... The two terms 5z and - 3z are

A: The two terms 5z2 and -3z2 are like terms.

Q: What is the worst-case distance between the bottom surface of the slot and the botto surface of the…

A: Given drawing

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.