Im not sure about the rest 3 part A tensile test generates the stress-strain diagram shown here.Stress (MPa)600500400300200100O0.00Stress (MPa)0.0450040030020010000.0000.08Strain0.002 0.004Young's modulus numeric value equal toYoung's modulus value obtain fromYield strength value obtain fromYield strength numeric value equal toAssume a tensile specimen was originally 10cm long with 2 cm x 2 cm square shape cross section.Tensile strength numeric value equal toTensile strength value obtain fromStrain0.120.00610.160.20The change in sample length while a stress of 480 MPa is applied to a tensilespecimen200 GPaslope of linear part of t400MPadraw a line from 0.002 v[Choose ][ Choose ][Choose ] [Choose ]510 MPa0.20 mdraw a line from 0.002 strain parallel to linear portion of the plot and intercept the plot400 MPanot changeslope of linear part of the plotmaximum strain510 GPa200 MPafinal fracture point of the curve300 GPadraw a line from 0.002 strain straight up (parallel to y axis) and intercept the plot300 MPa200 GPa0.1850.110400 GPalinear portion shift to curve line0.20 mm4

In this problem, it is asking about the last 3 sub-parts.

A tensile test generates the stress-strain diagram shown here. 600 Stress (MPa) 500 400 300 200 100 T 0 0.00 Stress (MPa) 0.04 500 400 300 200 100 0.000 0.08 Young's modulus numeric value equal to Young's modulus value obtain from 0.002 0.004 Yield strength numeric value equal to Yield strength value obtain from Strain Assume a tensile specimen was originally 10 cm long with 2 cm x 2 cm square shape cross section. Tensile strength numeric value equal to Tensile strength value obtain from Strain 0.12 0.006 0.16 0.20 The change in sample length while a stress of 480 MPa is applied to a tensile specimen 200 GPa slope of linear part of tl ✓ 400 MPa draw a line from 0.002 ✓ [Choose ] [Choose ] [Choose ] < <

A tensile test generates the stress-strain diagram shown here. 600 Stress (MPa) 500 400 300 200 100 T 0 0.00 Stress (MPa) 0.04 500 400 300 200 100 0.000 0.08 Young's modulus numeric value equal to Young's modulus value obtain from 0.002 0.004 Yield strength numeric value equal to Yield strength value obtain from Strain Assume a tensile specimen was originally 10 cm long with 2 cm x 2 cm square shape cross section. Tensile strength numeric value equal to Tensile strength value obtain from Strain 0.12 0.006 0.16 0.20 The change in sample length while a stress of 480 MPa is applied to a tensile specimen 200 GPa slope of linear part of tl ✓ 400 MPa draw a line from 0.002 ✓ [Choose ] [Choose ] [Choose ] < <

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cable is attached to a 1.40 kg block A, is looped over a fixed peg at C, and is attached to plate B.(Figure 1) The coefficient of static friction between the plate and the block is u4 = 0.150, the coefficient of static friction between the plate and the inclined plane is uR = 0.300, and the coefficient of static friction between the cable and the peg is uç = 7.00x10-2. If the plane's angle is 30.0 degrees, what is the maximum mass that plate B can have such that it does not slide down the plane? Express your answer numerically in kilograms to three significant figures. • View Available Hint(s) vec ? mB = kg
I need , RAy and RBy with complete solution write it on a paper. Thank you for helping.
Mechanical engineering 　５
or with в ст Ey X This pic is a 29 см I KNM __ X BUE 26cm right Triangle that made from from rods IL 8 11 pogon Find The location of the center of gravity ? 20 O a Constant cross-sectional area
3. Column ABC has a uniform rectangular cross-section and is braced in the xz plane at its midpoint C is shown Figure Q3(a). Given, the factor of safety is 2.7, P=5.4 kN, L=600 mm and E=70 GPa, determine the ratio b/d for which the factor of safety is the same with respect to buckling in the xz and yz planes
When a particle is subjected to both gravitational and elastic forces, the resultant force is expressed as which force?
An electric hot water heater consumes 3.1 kilowatts of electricity and converts it to heat. How long will it take the water heater to heat a 67 gallon tank of water from 10 degrees Celsius to 50 degrees Celsius? (1 kilogram of water is 0.37 gallons, 1 Calorie = 4200 J). It may be helpful to refer back to the weekly handout for guidance on this problem. Your final answer should be in minutes (rounded to the nearest 10 minutes).
C Mississippi Jane is at it again! The big bad evil one has trapped her on an accelerating conveyor belt with a rolling pipe - or so it seems. The pipe is actually not there and instead to be added in during post production for the actress' safety. It is up to you to calculate the proper physics of the pipe so that the CGI pipe may look as realistic as possible. If the pipe is meant to have a mass of 500 (kg) and a mean radius of 0.55 m, determine the pipe's angular acceleration if the conveyor belt has an acceleration of 1.9 Assume the pipe does not slip on the conveyor belt and neglect its thickness. m 82 α= 3.5 X rad 2 сс UBC Engineering
2 what are two examples of non planar motions
I need help with the second table. and these questions 1- If 1 gallon of oil = 1.4 therm, how many gallons have been wasted by heat loss in Feb? (1 therm = 100,000 BTU) 2- If $1.30 per therm, how much did you waste from house heat loss in Feb?
The two blocks A and B have a mass of 5.4 kg and 13 kg , respectively- (Figure 1) Figure 1'of 1
If you exhale slowly on a cold day, your breath becomes visible. Why? It’s not rising or falling a great distance.