A tensile load of 190 kN is applied to a round metal bar with a diameter of 16 mm and a gage length of 50 mm. Under this load the bar elastically deforms so that the gage length increases to 50.1349 mm and the diameter decreases to 15.99 mm. Determine the modulus of elasticity and Poisson"s ratio for this metal.

Q: Determine the young modulus and the poisson's ratio of this steel.

A:

Q: A solid round bar of diameter 250mm has a tensile force of 0.2kN acting on it. What is the stress…

A:

Q: . A sheet of plywood consists of three equally thick sheets, the upper and lower sheets having their…

A: Given   Tensile modulus, E1 = 10 GPa                              E2 = 0.4 GPa Find   Tensile…

Q: Question 53 What is the elongation of the aluminum bar with a dimension of 25 mm by 25 mm and length…

A:

Q: If the stress is 33 MPa and Modulus of elasticity is 58.7 MPa. What is the strain value. Apply hooks…

A: Given data Stress= 33mpa Modulus of elasticity= 58.7 mpa  We have to find strain value

Q: A sheet of plywood consists of three equally thick sheets, the upper and lower sheets having their…

A: Given   Tensile modulus, E1 = 10 GPa                              E2 = 0.4 GPa Find   Tensile…

Q: A bar of chocolate has length, thickness, and width measurements of 15mm each. The load applied to…

A:

Q: A tensile test uses a test specimen that has a gage length of 50 mm and an area = 200 mm². During…

A:

Q: consider a specimen having a length L of 200 mm and diameter D of 5 mm subjected to a tensile = F of…

A:

Q: Two solid cylindrical rods support a load of P = 39 kN, as shown. Rod (1) has a diameter of 16 mm…

A:

Q: A tensile test specimen has a gage length = 3.0 in and diameter 0.75 in. Yielding occurs at a load…

A: In order to determine the tensile strength of the specimen, the maximum load and area of cross…

Q: A torsion test shows that the shear modulus of an aluminum specimen is 4.60 x 10^6 psi. When the…

A: Material elastic properties E is modulus of elasticity G is modulus of rigidity K is Bulk Modulus…

Q: A bar of 80 mm diameter is tested in tension. It is observed that when a load of 90 kN is applied,…

A: The given data are: Here, d denotes the diameter, P denotes the load, and L denotes the length.

Q: A solid aluminum shaft of 112 mm diameter fits concentrically in a hollow steel tube. Determine the…

A: To find: The minimum internal diameter in mm of the steel tube. Given: The diameter of the shaft is…

Q: At the proportional limit, a 31 mm wide by 14 mm thick bar elongates 2.1 mm under an axial load of…

A:

Q: Find the elongation when it is subjected Select one: Ⓒa. 0.004 mm b. 0.4 mm c. 0.0004 mm d. 0.04 mm…

A: Given data: ◆ The length of the steel rod: L = 100 mm ◆ The tensile strain in the rod: ε = 0.004…

Q: 1. A steel pipe of length 4 ft, outside diameter of 6.0 in., and inside diameter of 4.5 in., is…

A:

Q: Problem 2 A cylindrical specimen of a nickel alloy hav- ing an elastic modulus of 207 GPa (30 x 106…

A:

Q: A compressive load of 2.4 kN acts on a circular bar of 200 sq. mm area and 20 mm high. It…

A: Load P=2.4 kNArea A=200 mm2Length/height L=20 mmCompression To Find-The value of Young's modulus of…

Q: You are given a square rod of 6061-T6 aluminum (cross-section = 4mm X 4mm, length = 2.3m).  The…

A:

Q: Q4/ Determine the total elongation of an initially straight bar of length 100 cm, with diameter is…

A:

Q: The brass has a shear modulus (G) of 40 GPa. In the torsion test calculated results. (G) was found…

A:

Q: At the proportional limit, a 22 mm thick 75 mm wide bar elongates 6.3 mm under an axial load of 482…

A:

Q: A tensile load of 20 kN is applied on a wire made of a copper alloy having an elastic modulus of 120…

A:

Q: composite column is formed by placing a steel bar 20 mm diameter and 200 mm long, inside an alloy…

A:

Q: At the proportional limit, a 24 mm thick x 69 mm wide bar elongates 6.8 mm under an axial load of…

A: Given that ,  Elongation =6.8mmAxial load=453kN Length of bar l=1.8m Poison ratio=0.3

Q: An circular rod loaded with 30,000 lbs. The allowable tensile stress is 10,000 psi, modulus of…

A:

Q: A metal block of cross-section area A and length L is subject to a tensile stress of S. The block…

A:

Q: In a standard tensile test a steel rod of 7/8 in. in diameter is subjected to a tension force of 17…

A: given data - v= 0.25 to determine - ratio of G/D

Q: A tensile load of 40 kN is acting on a rod of diameter 40 mm and of length 4m. A bore of diameter 20…

A:

Q: A tensile forceo f 100 kN is applied on a 0.02-m diameter and 2-m long rod. After applying the load,…

A: Given: The tensile force is F=100 kN. The initial diameter is do=0.02 m. The initial length of the…

Q: Two vertical wires are suspended at 450 mm apart. Their lower ends support a rigid horizontal bar…

A:

Q: A square bar subjected to a tensile load of 100KN having a gauge length of 200mm, extends to a…

A:

Q: At the proportional limit, a 18 mm thick 84 mm wide bar elongates 6.9 mm under an axial load of 495…

A: The change in width of the bar is -0.1242 mm.

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.