An circular rod loaded with 30,000 lbs. The allowable tensile stress is 10,000 psi, modulus of elasticity of 40x106 psi. If the original length of specimen is 35 inches with elongation not exceeding 0.0015 inch, what diameter of the rod is required? O a. 4.72 in O b. 1.954 in OC.1.215 in O d. 5.923 in

An circular rod loaded with 30,000 lbs. The allowable tensile stress is 10,000 psi, modulus of elasticity of 40x106 psi. If the original length of specimen is 35 inches with elongation not exceeding 0.0015 inch, what diameter of the rod is required? O a. 4.72 in O b. 1.954 in OC.1.215 in O d. 5.923 in

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1.4 (A). Twe fork-end pieces are to be joined together by a single steel pin of 25 mm diameter and they are required to transmit 50 kN. Determine the minimum cross-sectional area of material required in one branch of either fork if the stress in the fork material is not to exceed 180 MN/m2. What wili be the maximum shear stress in the pin' [1.39 x 10-m'; 50.9 MN/m] 1.5 (A) A simple turabuckle arrangement is constructed from a 40 mm outside diameter tube threaded internally at each end to take two rods of 25 man outside diameteT with threaded cnds. What will be the nominal stresscs set up in the tube and the rods, ignoring thread depth, when the turabuckle carries an axial load of 30 kN? Assuming a suficient strength of thread, what maximum load can be transmitted by the turnbuckle if the maximum stress is imited to 180 MN/m? [39.2, 61.1 MN/m2, 88.4 kN.]
Question 5: The following 0.8" diameter steel bar has three loads applied, as shown. Assuming that E= 30,000,000 psi, determine the following: Stress at points A, B, and C Total elongation of the bar. Hint: 8- PL AE オー 2000 Ibs 2-0" 4000 Ibs I-0 7000 Ibs
A specimen is originally 1.5 ft long, has a diameter of 0.7 in., and is subjected to a force 550 lb. When the force is increased to 1900 lb, the specimen elongates 0.9 in. Determine the strain on the specimen and the modulus of the material. a. Strain Answer: _______ in./in. b. Modulus of Elasticity Answer: _______ ksi
A tensile force. of 120 kN is applied on a 0.02-m diameter and 2-m long rod. After applying the load, the diameter decreases to 0.01998 m and the length increases to 2.01 m. The true stress on that rod is?
1. At a point in a piece of elastic material, direct stresses of 92 MN/m2 tensile and -49 MN/m2 compressive are applied on mutually perpendicular planes. The planes are also subjected to a shear stress. If the greater principal stress is limited to 100 MN/m2 tensile, determine the value of shear stress. Give you answer to 2 significant figures in MN/m2
Determine the compressive force (in Ib) in the bars shown after a temperature rise of 149°F if d = 0.012 in. Round off the final answer to five decimal places. d ... L M Use the following data: Bronze Aluminum A = 2.24 sq. in A = 2.73 sq. in E = 14930924 psi L = 13.4 in E = 10543748 psi L= 16 in a = 11.76 x 10-6/ °F a = 12.54 x 10-6/°F
1200 N 2. For the bone shown to the left, assume the cross-section at C can be approximated as annular, with an outer diameter of 25mm. When the 1200 N forces are applied, the average normal stress in the bone at point C is determined to be 3.80 MPa. Determine the inner diameter of the bone cross section at C. Ans: d; = 14.93 mm 4 in. P 3 in. B 1200 N "UI 8
2.412 KIV 3. A square aluminum bar is to support a load of 40 kN on a length of 3 m. Assuming pinned ends, determine the length of each side.
The pressure in a cast-iron water pipe is 180 psi. If the inside diameter of the pipe is 15 in. and the allowable unit stress in tension is 2000 psi, what should be the thickness of a shell of the pipe, expressed as a multiple of 1/8 in. A. 3/4 in. B. 5/8 in. C. 1/2 in. D. 3/8 in.