1-41. The constants B = 1.357(10-6) N-s/(m² -K!/2) and C = 78.84 K have been used in the empirical Sutherland equation to determine the viscosity of air at standard atmospheric pressure. With these constants, compare the results of using this equation with those tabulated in Appendix A for temperatures of T = 10°C and T = 80°C. %3D

1-41. The constants B = 1.357(10-6) N-s/(m² -K!/2) and C = 78.84 K have been used in the empirical Sutherland equation to determine the viscosity of air at standard atmospheric pressure. With these constants, compare the results of using this equation with those tabulated in Appendix A for temperatures of T = 10°C and T = 80°C. %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A moving load at a speed of 4.09 mph hạs a tire pressure of 80 psi and a tire contact radius of 6…

Q: A piston having a cross-sectional area of 0.18 m² is located in a cylinder containing water as shown…

Q: Determine Poisson's ratio if a cylindrical rod is placed in tension as shown and it is elastically…

A: Poisson's ratio can be defined as a ratio of Lateral strain to longitudinal strain. Poisson's ratio…

Q: Consider the beam shown in (Figure 1). Suppose that a = 12 in., b = 10 in., c = 1 in., and d = 4 in.…

Q: A piston having a cross-sectional area of 0.29 m² is located in a cylinder containing water as shown…

A: To find out the Applied force (p) acting on the piston.

Q: A piston having a cross-sectional area of 0.17 m² is located in a cylinder containing water as shown…

A: Solution: Given: A=0.17m2 h1=69mm=0.069m h=101mm=0.101m

Q: Radius of a right circular cylinder is measured with an error of at most 5%, and the height is…

Q: 3Q. At normal atmospheric conditions, approximately what pressure in MPa must be applied to water to…

Q: 100 mm 75 mm 25 mm 75 mm

Q: The figure below represents equilibrium. 85 N 60 N 45 100 N 30 F

Q: 14 For the machine element shown, locate the y coordinate of the center of gravity. Given: r= 1.5

A: -2.55

Q: An assembly consisting of an outer steel tube and inner brass rod is compressed with a load P = 125…

Q: what value of atmospheric pressure in psi, and in pascals?

A: Solution: 1 atm = 14.7 psi = 1.0325 x 105 Pa = 76 m of Hg = 29.9213 in…

Q: In a laboratory experiment it was found that the pressure drop Ap depends on the gate opening h, the…

Q: QIJ Give the reason behind the followings: 1- All gases can be considered as compressible fluids. 2-…

A: Fluid mechanics is the branch of physics which deals with the fluid and forces in it. It has…

Q: A steel tire has a dimensions indicated in the figure below. At 78 degrees Celsius, the said tire…

Q: Q1:- Consider a large cubic ice block of (1 m) surface area floating in seawater. The specific…

A: The above question is based on the archimedes principle, the loss in weight of the submerged body is…

Q: In the figure below, a pool of liquid sodium is sitting in open atmosphere (and somehow not…

A: 22

Q: Please solve True value density (kg/m3) and Percentage of Error

Q: Wo

A: A loaded beams have been given and it has been asked to determine shear force, bending moment…

Q: the surface tension of water in contact with air at 20c is given as 0.0716 n/m. the pressure inside…

A: Given Data:- Surface tension σ=0.0716 nm Excess Pressure inside droplet of water ∆P = 0.0147ncm2…

Q: A gasoline line is connected to a pressure gage through a double-U manometer, as shown. If the…

Q: A 50-m steel tape standardized at 20° was found to be 50.16 m long. This tape was held horizontal to…

A: The original length of tape, L =50mThe length of tape at standardized temparature =50.16mThe…

Q: kmown that the tersile strengthof plastic increases as a function of time it is heated. The…

A: To find:- tensile strength at a time of 43 min

Q: Q1: make introduction relating to all topics? 1. Shear force and bending moment on skateboard 2.…

A: Introduction 1. shear force and bending moment on skate board : When constructing a building, it's…

Q: Determine the moment of inertia Ix (m.“) of the shaded area about the centroid. Type your answer in…

Concept explainers

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.

Question

100%

1-41. The constants B = 1.357(10-6) N-s/(m² -K!/2) and
C = 78.84 K have been used in the empirical Sutherland
equation to determine the viscosity of air at standard
atmospheric pressure. With these constants, compare the
results of using this equation with those tabulated in
Appendix A for temperatures of T = 10°C and T = 80°C.
%3D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

% 6 5:05M. docs.google.com/draw Thermal Stress 5 File Edit View Tools Help View only Four steel bars jointly support a mass of 15 Mg as shown. Each bar has a cross-sectional area of 600 mm2. Find the load carried by each bar after a temperature rise of 50°C. Assume a = 11.7 µm/(m "C) and E = 200 GPa D 60⁰ 15° 15° 15 Mg { | | 44% - ||| e 9
A steel tape, with a coefficient of linear expansion of 0.0000116/C, is known to be 100 meters long at 20°C. The tape was used to measure a line was found to be 1532.28 meters long when the temperature was 37°C. Determine the following: Temperature correction per tape length Temperature correction for the measured line Correct length of the line
Please show your solution on a paper with FBD
A steel tape, with a coefficient of linear expansion of 0.0000116/C, is known to be 50 meters long at 30°C. The tape was used to measure a line was found to be 15532.28 meters long when the temperature was 27°C. Determine the following: a. Temperature correction per tape length b. Temperature correction for the measured line c. Correct length of the line
The pressure read on the pressure gauge of the system in the figure is 65 kpa. Considering the data shown, determine the height difference "h" on the differential pressure gauge. Aire = air Agua = water Aceite = oil Mercurio = mercury
QUESTION 21: A 50m tape of standard length has weight of 0.05kg/m, with a cross sectional area of 0.04sqcm. It has a modulus of elasticity, E = 2x106 kg/cm² The tape is of standard length under a pull of 5.5kg when supported throughout its length and a temperature of 20°C. This tape was used to measure a distance between A and B and was recorded to be 458.65m long. At the time of measurement, the pull applied was 8kg with the tape supported only at its endpoints and the temperature observed was 18°C. Assuming coefficient of expansion of steel tape as 0.0000116/°C. a) Compute the correction due to the applied pull. b) Compute the correction due to sag of the tape. c) Compute the true length of the measured line AB due to the combined effects of applied pull, sag and temperature.
In the following table, a part of a project, for which the time period for each activity is specified, find the time required to complete the project using the network diagram by Act. on arrows. Activity A B D G H I Time Followed by Preceded by B.C 23573625 G.F D.F E I I H I A A C B.C DBG H.E.F
In an experiment to determine the viscosity of some oil, a ball is dropped into the oil. The position of the ball is given by the formula y(t) = A + Bt +C e−Dt, where y is given in m, and t is the time in s. At t = 0, y(0) = 0.05 m, the y component of the velocity is zero and the y component of the acceleration is ay(0)= 0.02 m/s2. As t approaches infinity, the y component of the velocity approaches vy(∞) = 0.55 m/s. Hint: You will likely want to answer the questions in a different order than presented. I am trying to figure this qeustion out, I need to find out what each of the variables in the fromula are. So far I have only found out what B is because I just toook the limit of the velocity function as t approaches zero, which gave me 0.55m/s. I am just stuck on how I would go about solving for the other variables in the question.
the surface tension of water in contact with air at 20c is given as 0.0716 n/m . the pressure inside a droplet of water is to be 0.0147 n/cm2 greater than the outside pressure, calculate the diameter of the droplets of water?
M27
A barometric pressure of 50 in. Hg corresponds to what value of atmospheric pressure in psi, and in pascals? (a) p = (b) p = psi Pa
to measure a base line, a steel tape 30m long standardised at 15 degree Celsius with a pull of 100N was used. Find the correction per tape length, if the temperature at the time of measurement was 20 degree Celsius and the pull exerted was 160N weight of 1cm3 of steel is 0.0786N and weight of the tape=8N, E=210000kg/m2, coefficient of expansion of tape per 1 degree celsius is 0.00000071.