A submersible cylinder used in research has a cylindrical pressure hull of outside diameter 3.0 m and a wall thickness of 150 mm. It is constructed of an aluminum alloy, having a yield point of 450 MPa. Determine the tangential stress, in terms of MPa, in the

Q: the differences between CAD, CAE, CAM and CIM.

A: CAD:- Computer-aided design is defined the practice of using the computer systems in order to help…

Q: Determine total indeterminacy and external indeterminacy

A: Given data : Number of external support reaction (R)=2+1+2=5Number of member (m)=8Number of joint…

Q: How to determine Z-value? How to determine D-value and TDT?

A: The Z-value is referred to calculation of the resistance of micro-organism at different temperatures…

Q: d. Secant modulus at a stress of 62 ksi. e. Tangent modulus at a stress of 65 ksi.

A: Given data:- Stress - strain relationship shown in below;

Q: Compute the total length of 10 mm diameter stirrups for a beam section 500 mm x 250 mm. Total length…

A:

Q: Determine the centroid of the shaded area shown, which is bounded bythe X axis and the parabola y? =…

A:

Q: & Find the set of solutions xy dx + (y-3x²) dy = 0. %3D

A:

Q: -160 40 160 Dimensions 40 in mm 40 -160- –160-

A:

Q: complete the following set of profile level notes and show the customary arithmetic check.

A: Height of instrument method:HI=Elv+BMElvi+1=HIi-FS or ISExampleHI at BM-a:HI=234.51+1.24=235.75Elv…

Q: Explain the formula of fs

A: From the original solution: Given: Width, b = 18 in Effective depth, d = 26.5+2.5=29 in. Height of…

Q: Name this force system Question 18 options: Non-planar concurrent…

A: To name the force system.   Coplanar force system, is one in which all the forces lie in the same…

Q: A clockwise couple M = 4.5 N m is resisted by the shaft of the electric motor. (Figure 1) Part A…

A: Given: The moment M is 4.5 N.m. Consider the figure,

Q: discussfineness modulus

A:

Q: entify the outfall entify the peaks entify the valleys

A: Watershed: A watershed depicts an area of land that contains a typical arrangement of streams and…

Q: Determine the XT and YT(using both a and b) a. Using the Top Most, Left Most Reference Line b. Using…

A:

Q: You are a professor of architecture. Show your students where the horizon line and vanishing points…

A:

Q: Complete the following set of profile level notes and show the customary arithmetic check.

A: Formula: Height of instrument methodHIi=Elevi+BSiElvi+1=HIi-FS or BSi+1example:at Station…

Q: aSN 200 mm 350 mm

A: Free Body Diagram (FBD):

Q: There are support reactions Ay and By which both equal 3.5kN going upwards.

A:

Q: Determine the coordinates of the centroid of the shaded area. y 15 E 30 35 15 40 50 I 30 - x 100…

A:

Q: CORRECT ANSWER

A:

Q: 200 mm 200 mm 400 mm

A: Section  Area  x Remarks  ABC A1  = π42002      = 31400 mm2 x1 = D2    = 2002     =100 mm   AEF…

Q: 80 38 24 340 R24 25 R40 130

A: It is not possible that every command and steps that is used in the drawing is to write down here…

Q: 3. A simply supported beam of 6 m, see cross-section below is subjected to a concentrated load of…

A: Using bending equation

Q: What is the distance between the kerns for the section given below? K- 100- 50 200 50 50

A:

Q: Part A What is the ratio scale for the equivalent scale of 1 in. = 80 ft? Express your answer using…

A: 1 ft =12 inch given 80 ft =12*80=960in Ratio scale=112×80=1:960

Q: х у The value of |2y + z y [2z + x [2x + y z is

A:

Q: 3. Is Iust be par PROBLEM 1: The frame shown is supported with hinges at A and C and a pin at B.…

A: Both the hinges will have the two supports, they are :- RAx and RAy at A and RCx and RCy at C. Then…

Q: 10 20 10 +¹0| -25 30 20, 70 Dimensions in millimeters x Break the shaded area into the five…

A:

Q: sanitary engineering  solve by hardy Cross method  k=8*f*L/pi*g*D^5 f=0.02 g=9.81 pi=e.14

A: Given data in question  Length of pipe  Diameter of pipe Constant value of f Acceleration due to…

Q: 100 N 100 N 100 100 150 250

A:

Q: If Ax B = = A.B then the angle between A and B will be %3D a) п b) π/2 ) π/3 TE e) None of the above…

A: To find angle between A and B

Q: 150 25 40 185 25 75 50

A: To draw the front, top and side view of the given object. Given 3d object:

Q: Y

A:

Q: Determine the centroid with respect to the indicated X and Y axes of the area shown. Present…

A: Given data in question  Dimensions 35 mm and 80 mm height Circle 15 mm radius Semi circle 35 mm…

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?