A student wants to determine how different factors affect the rate of dissolving a solid in water. Trial Size of Particles Rate of Dissolving small 10 sec 2 medium 20 sec 3 large 30 sec What procedures can be performed on trials 2 and 3 so that the rate of dissolving is the same as trail 1? The student can decrease the temperature The student can decrease the pressure O The student can increase the pressure The student can increase the temperature

A student wants to determine how different factors affect the rate of dissolving a solid in water. Trial Size of Particles Rate of Dissolving small 10 sec 2 medium 20 sec 3 large 30 sec What procedures can be performed on trials 2 and 3 so that the rate of dissolving is the same as trail 1? The student can decrease the temperature The student can decrease the pressure O The student can increase the pressure The student can increase the temperature

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

Procedure A: Molarity (M=g/MM/L) Step 1. Place one-eighth of a teaspoon (this weighs approximately 0.5 grams) of NaCl (table salt) in the graduated cylinder provided. Then add distilled water to that graduated cylinder until the level of the water reaches 45.00 mL. Mix thoroughly about 1 minute. Pour solution into a somewhat clear cup. Remember what this looks like for Procedure B. Questions: Is this a saturated solution? Why or why not? Take a picture and insert a picture (compress your image) of your solution here. Save this solution for Step 2. Calculations: Determine the Molarity of this solution using the formula M = g/MM/L. You know the grams (one-eighth of a teaspoon weighs approximately 0.5 grams), look up the Molar Mass of NaCl, and convert your mL to L to solve the problem.) Show your calculations for Molarity here. C % 31 D < hp & * ✔
You need to analyze an aqueous alcohol solution in the laboratory. You separated 367 mL of this solution and diluted with 40 mL of water. You then get 50 mL of the resulting solution and mixed with 50 mL 30% v/v aqueous alcohol solution. You analyzed the final solution and found out that it's concentration is 40% v/v alcohol. How much alcohol in mL does the initial solution contains?"
How many milliliters of a 3.9 M NaCl solution would be needed to prepare each solution? a. 35 mL of a 2.4 M solution: mL b. 170 mL of a 0.79 M solution: mL < Prev 15 of 16 M
In the laboratory you are asked to make a 0.170 m ammonium acetate solution using 455 grams of water. How many grams of ammonium acetate should you add? grams.
Four plz
Pls help ASAP ON ALL ASKED QUESTIONS PLS PLS
Data Table Mass of Zn HCI Volume Tinitial Tfinal 0.55 g 100.0 mL 20.0 °C 23.1°C The density of the 6M HCI is 1.07 g/mL. Which of the following shows how to convert the volume of the solution used into grams of solution? O a. 100.0 mL x 1mL 1.07 g Ob. 1.07 g 100.0 mL 1.07 g 1ml OC. 100.0 ml x The amount of heat absorbed by the solution can be found using the equation q = m x SH x AT. It can also be written as qsolution = msolution X SHsolution X ATsolution: We can assume that the specific heat of the solution is the same as the specific heat of water which is 1.00 cal/(g °C). Data Table Mass of Zn HCI Volume T;initial Tfinal 0.55 g 100.0 mL 20.0 °C 23.1°c Which of the following shows the correct calculation of gsolution? cal "x 3.1°C g°C O a. 100.0 mL x 1.00 Ob. cal 107 grams x 1.00 g °C х 3.1°C 0.55 grams x 1.00 cal х 3.1°C g °C
9. An enzyme stock solution is 100 µg/µL. The stock solution is serially diluted 4 times by a dilution factor of 1/50. What is the concentration of each dilution?
Use the graph on the last page to answer questions 10, 11 and 12. At 80˚C, what mass of sodiumchloride dissolves in1.0 L of water?
Pls help ASAP ON ALL ASKED QUESTIONS PLS PLS
What mass of cesium bromide must be added to 0.500 L of water d=1.00 to produce a 0.650 m solution? What are the mole fraction and the mass mL percent of CsBr? Be sure each of your answer entries has the correct number of significant figures. Part 1 of 3 Mass of cesium bromide = Part 2 of 3 Mole fraction= Part 3 of 3 Mass percent= % x10 g x10 X x10
The blood of a reckless driver contains 0.18% alcohol. The concentration of alcohol is equivalent to _____ ppm.