Consider the shear and moment diagram of a cantilvered beam. Determine the magnitude of the concentrated load (kip) acting at the free end of the beam. V (kip) 30.0 0 18.0 6 8.00 10 -x (ft) M (kip-ft) 0 -216 6 -72.0 10 +x (ft) -40.0

Consider the shear and moment diagram of a cantilvered beam. Determine the magnitude of the concentrated load (kip) acting at the free end of the beam. V (kip) 30.0 0 18.0 6 8.00 10 -x (ft) M (kip-ft) 0 -216 6 -72.0 10 +x (ft) -40.0

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The beam is subjected to a shear force of V = 25 kN. Determine the shear flow at points A and B. 12…

Q: A cantilever beam projects 2.8 m from the face of a wall. The beam is subjected to a 52 kN…

Q: a. Determine the reaction (R) b. Determine the end moment at wall (Mc) C. Determine the tangential…

Q: 3.6 - 0.6 E -2.4- 0.3 D 0.3 45° -1.2 0.6

A: To find force carried on link D

Q: Draw the LOAD (w) and the BENDIN shear force diagram. Assume that r

Q: Determine the internal normal force, shear force, and moment at point D in the beam. Draw free Body…

Q: For the given shear diagram shown: V (kN) 10 - 2nd-degree curve в с D E A x (m) -2 -8 3 2.

A: Shear force and bending moment diagram represent the forces acting and moments acting on the…

Q: 1. Compute Per the maximum displacement using Double-Integration aud Moment Area Met hod. Draw shear…

A: ##problem1 ### ##Double integration method ,, maximum deflection and sfd and bmd###

Q: Sketch the shear force and bending moment diagram for the compound beam shown in the figure. Assume…

A: Given data Draw shear force and bending moment diagram.

Q: 1. Determine the normal Force, Shear Force and Moment at F and E: (NF.NE,VF, VE,MF,ME,

A: The beam AEBC is taken seperately. Th reaction have to be calculated for beam AEBC. Thus the normal…

Q: 10 EN/m 2 Nim 2kN

Q: Consider the shear and moment diagram of a cantilvered beam. Determine the magnitude of the…

Q: Determine where the maximum displacement of the following beam is happening and what its value is.…

A: The free-body diagram of the beam given below Taking moment about Point…

Q: a. Determine the reaction (R) b. Determine the end moment at wall (Mc) C. Determine the tangential…

Q: A propped beam shown below is loaded with UDL along its entire span. Determine the following: a.…

A: Find reaction R Moment at C And deviation (tB/C)

Q: Given the beam loaded as shown below, determine: (a.)Equation of shear at segment BC for any…

Q: Determine the shear and moment diagram. Assume that Mo=200 lb.ft and L =20 ft

A: Introduction- Shear, as well as bending moment illustrations, are analytical techniques that are…

Q: 7 - For the given beam, the shear force diagram is illustrated as follows. Determine the maximum…

A: The point where the shear force is zero gives the location of the maximum bending moment. So, at x =…

Q: moment

Q: 2/88 If the resultant of the forces shown passes through point A, determine the magnitude of the…

A: Given data Point loads Span length Angle Tension

Q: 500 N/m 1,000 N 300 N/m 900 N-m 4 m 2 m Prepare an FBD to determine the location (m with two decimal…

A: To Find :- Location of resultant force from support B.

Q: Construct the shear and moment equations of the loaded beam as shown and draw the shear and moment…

Q: a. Determine the reaction (R) b. Determine the end moment at wall (Mc) C. Determine the tangential…

Q: PDL = 5 KN 500 mm Wp =6 KN/m WL =3 KN/m PLL = 3 KN 800 mm RI R: 2 m 1m 1 m

Q: A beam PQ is supported at its ends and loaded as shown. Draw the shear force and bending moment…

Q: M1 at point B is 10 kips-ft, P1=12 kips is 9 ft from point A; and w1 = 1.5 kips/ft is distributed…

A: Transformed singular concentrated load from UDL = 1.5 x 22 = 33 kips Magnitude of moment for the…

Q: Question 2: (recommended time-50 minutes) Beam AE is supported by a hinge at point 4 and a roller at…

A: Given, Simply supported beam with multiple loadings

Q: For the beam given in the figure, a) Find the support reactions. b) Draw the normal force, shear…

Q: M1 at point B is 10 kips-ft, P1=12 kips is 9 ft from point A; and w1 = 1.5 kips/ft is distributed…

A: Solution: Convert the udl into singular concentrated load: P2=load x length =1.5 ×22P2=33 kN The…

Q: A propped beam shown below is loaded with UDL along its entire span. the foll

Q: Two forces and a couple are applied to the beam in an attempt to lift it. Replace this force system…

A: Given data:

Q: M1 at point B is 10 kips-ft, P1=12 kips is 9 ft from point A; and w1 = 1.5 kips/ft is distributed…

A: M1=10kips P1=12kips To find resultant force and it's location from point A

Q: A drawbridge has mass M and length L and is approximately uniform. It has a hinge at the right end,…

Q: A cantilever beam projects 2.8 m from the face of a wall. The beam is subjected to a Y KN…

Q: roblem 5: Beam ABCDE is loaded as shown. The beam is supported by a fixed end at A and a roller…

Q: A beam is loaded as shown below. U1- 32 KN/m; M1 = 100 kN-m, and P1 = 120 kN. 32 M- 100 16 m) P- 120…

A: M1 = 100KNm P1= 120KN

Q: 11 From the continuous beam shown, it carries a uniform load fro A to B and a concentrated load P at…

A: Given Data Find a. Fixed end moment b. Distribution factor c. Moment at B Using Moment…

Q: Solve the support reaction at C. 16 k 2 k/ft 8 k 3 k/ft A D B. E F C 12 ft 8 ft- 9 ft 12 ft 9 ft 3…

A: To Determine Support Reaction at C , Cy

Q: A propped beam shown below is loaded with UDL along its entire span. Determine the following: a.…

Q: 9000 N/m 6000N 8000 N/m A 4 m 22m 2m 4 m DIE

Q: It is desired to obtain the loading and bending moment diagram corresponding to the given shear…

A: Given shear force diagramTo check the correct options A. There is a UDL acting on the beam of 8 kN/m…

Q: Q1/ For the beam shown below: 1- Draw the shear and moment diagrams. 2- Determine the absolute…

Q: Structural Theory Sketch the shear and moment diagram for the beam loaded shown. 6kN/m 10kN 4kN/m…

A: Given Data:Total span = 6mUvL=6kN/mUDL=4kN/mConcentrated load = 10kN Sketch the shear and moment…

Question

Consider the shear and moment diagram of a cantilvered beam. Determine the magnitude of the concentrated load
(kip) acting at the free end of the beam.
V (kip)
M (kip-ft)
30.0
0
18.0
6
8.00
+x (ft)
10
0
-216
6
-72.0
10
-x (ft)
- 40.0

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: State given data

VIEW

Step 2: Calculate force at free end

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

9 ft 13 ft 22. Inad nianram Mj at point B is 10 kips-ft, P=12 kips is 9 ft from point A; and WI = 1.5 kips/ft is distributed along the length of the beam which is 22 ft. If the 1.5kips/ft uniformly distributed load will be transformed into a singular concentrated load, what will be the magnitude of Moment taken at point A? What is the equivalent singular Resultant force of the loads shown? Determine the location of the resultant R from point A.
need pls fast
For the Beam and loading shown Determine bending moment at A in KN.m IF W= 41, a=1 m w kN w kN/m 2w kN m A . B ra m- a m→-a m a m А. -123.0 В. -205.0 C. -41.0 D. 0.0 Е. -20.5
$4. y Its weight in the tigure is negligible AE of the beam shear force and bending moment diagrams to draw. Pg = 30 kN -3 m E -4 m 3 m В D Cp = 40 kN - m
A propped beam shown below is loaded with UDL along its entire span. Determine the following: a. Determine the reaction (R) b. Determine the end moment at wall (Mc) C. Determine the tangential deviation at point B with respect to point C (t B/C) A d 4kN/m Ţ 3M
The distributed loading is acting on the cantilever as shown. If q = 15 kN/m, determine the moment of the loading about point A. A 1m x 1m ||dr B
Dead Load= 30 kN/mLive Load= 20 kN/mCompute and draw the Shear and Moment Diagram. Compute the maximum moment. Note: Please hurry up, I'll need it today.
9
Determine the vertical displacement of end B of the cantilevered 6061-T6 aluminum alloy rectangular beam. Consider both shearing and bending strain energy.