A steel tension bar 10-mm thick and 50-mm wide with an initial single-edge crack of 10-mm long is subjected to a uniaxial stress o = 150 MPa. Using the values given in Table Q4 below A) Determine the stress intensity factor KI. If KIC = 50 MPa m, is the crack stable? B) Determine the critical crack size. C) Determine the critical load. Take Y= 1.37

A steel tension bar 10-mm thick and 50-mm wide with an initial single-edge crack of 10-mm long is subjected to a uniaxial stress o = 150 MPa. Using the values given in Table Q4 below A) Determine the stress intensity factor KI. If KIC = 50 MPa m, is the crack stable? B) Determine the critical crack size. C) Determine the critical load. Take Y= 1.37

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A glass consists of cracks at surface and interior side. The surface crack lengths are s 5 um, the cracks at the interior are < 20um, and the average crack length is 8 µm. The glass is exposed to tensile stress. a) What is the maximum stress the glass can withstand? b) What is the maximum compressive strength? J/m = Pa/m? Given, y = 1 J m² and Y = 70 GPa. Kịc Ofail = Z TCavg Z = 15
An aircraft component is fabricated from an aluminum alloy that has a plane strain fracture toughness of 31 MPa/m. It has been determined that fracture results at a stress of 227 MPa when the maximum (or critical) internal crack length is 2.47 mm. a) Determine the value of Yo√a for this same component and alloy at a stress level of 340 MPa when the maximum internal crack length is 1.24 mm. i MPa √//m b) Under these circumstances will the component fail? No Yes Unable to Determine 3
250 Stress (MPa) 200 150 100 50 0.10 Q3. Using Figure 2 determine the: A). 0.2% offset yield strength B). Ultimate Stress Stress (MPa) 150 100 50 0.20 Strain Figure 2 Strain 0.005 0.30 C). Using Figure 2, determine the sample length at fracture, if the initial length was 10 cm. 0.40
A bronze alloy specimen having a diameter of 12.8 mm and a gage length of 50 mm was tested to fracture. Stress and strain data obtained during the test are shown in Figure. Determine: 400 - Upper scale a. the modulus of elasticity. 320 b. the proportional limit. Lower scale c. the ultimate strength. 240 d. the yield strength (0.20% offset). 160 e. the modulus of resilience. f. the true fracture stress if the 80 final diameter of the specimen at the location of 0.100 0.005 0.300 0.015 0.200 0.400 the fracture was 10.5 mm. 0.010 0.020 g. The Poisson's ratio. Strain (mm/mm) Stress (MPa)
1. A bronze alloy specimen having a diameter of 12.8 mm and a gage length of 50 mm was tested to fracture. Stress and strain data obtained during the test are shown in Figure. Determine: 400 Upper scale a. the modulus of elasticity. b. the proportional limit. c. the ultimate strength. 320 Lower scale 240- d. the yield strength (0.20% offset). 160 e. the modulus of resilience. f. the true fracture stress if the 80 final diameter of the specimen at the location of the fracture was 10.5 mm. 0.100 0.200 0.300 0.400 0.005 0.010 0.015 0.020 g. The Poisson's ratio. Strain (mm/mm) Stress (MPa)
Sketch a representative stress-strain digrama for a ductile material showing the following on it (label the axis and provid units). 1- YIELD STRENGTH. 2- TENSILE STRENGTH. 3- FRACTURE POINT. 4- HARDENING PART. 5- SOFTENING PART. 6- A METHOD TO CALCULATE THE STIFFNESS. 7- A METHOD TO CALCULATE THE DUCTILITY.
1. For the stress-strain curve shown below, please estimate the properties indicated. (a) Fracture Strain Please do your work on a separate sheet of paper, and put your answers in the boxes on the right. Be sure to include the proper symbol and units. Stress Strain 70 60 50 Stress (ksi) 240 30 20 10 70 0 0.000 60 50 Stress (ksi) 40 20 10 KULL 0 0.000 0.010 0.050 0.100 Strain (in/in) Stress Strain 0.020 0.030 Strain (in/in) 0.040 0.150 0.050 (b) Ultimate Tensile Stress (c) Fracture Stress (d) Proportional Limit (e) Elastic Modulus (1) Yield Stress (g) Tensile Toughness (Modulus of Toughness) (h) Modulus of Resilience
ASAP
2) Use the engineering stress strain diagram provided below to answer parts (A) to (H) below (the stress-strain diagram has already been drawn for you): stress strain diagram 400 350 0 300 0 250 0 200 0 150.0 100.0 50.0 00 0 05 01 0. 15 strain A. Determine the tensile strength of this alloy. B. show the clastic, plastic and total strain on the diagram stress (Mpa)
A thin-walled cylinder of a high-strength aluminumalloy (KIC = 24 MPa √m ) has the following dimensions:length = 20 cm; outer diameter = 9 cm; inner diameter7 cm. A semicircular crack of depth a = 0.25 cm is discovered on the inner diameter and oriented along a line parallelto the cylinder axis. If the cylinder is repeatedly pressurized,how many pressure cycles could the cylinder withstandbefore failure? The pressure within the cylinder reaches75 MPa, and the material obeys a fatigue crack propagationrelation of the formda/dN = 5 x 10-39(ΔK)4where da/dN and ΔK have the units of m/cycle and Pa √m ,respectively.
Compute the minimum critical surface crack (edge crack) length if the fatigue life must be a minimum of 5.0 x 106 cycles. Assume the initial maximum edge surface crack length of 1.80 mm and a maximum tensile stress of 160 MPa and minimum stress of 0 MPa. Assume m = 1.8 and A= 7.5 x 1013 in MPa and meter units, Assume Y= 1.25. O a. 4.26 mm O b. 5.38 mm OC. 2.36 mm O d.0.125 m
A Copper specimen of circular cross-section is subjected to a tensile test. The data obtainedare:Length of Specimen = 329 mm;Diameter of Specimen = 39 mm;Load at Yield Point = 130 kN;Maximum Load = 219 kN;Load at fracture = 118kNDetermine the following:1) Find initial area of the test specimen2) Yield Stress3) Ultimate Stress4) Fracture stress5) Find the strain for 0.058mm elongation.6) Mark Yield stress, Ultimate stress and Fracture stress on a Stress-Strain diagram.