A steel rod (E= 200 GPa) is subjected to the load shown, where P = 2500 kN . A gap a = 2.00 mm exists before the load is applied. The elongated rod contacts the top surface at C'. Assume the mass of the rod is negligible. The values for the figure below are d = 0.750 m , e = 0.400 m, j= 59.0 mm, and g = 44.0 mm

A steel rod (E= 200 GPa) is subjected to the load shown, where P = 2500 kN . A gap a = 2.00 mm exists before the load is applied. The elongated rod contacts the top surface at C'. Assume the mass of the rod is negligible. The values for the figure below are d = 0.750 m , e = 0.400 m, j= 59.0 mm, and g = 44.0 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

200KN A steel rod is rigidly attached between an aluminum and bronze rod. The diameters of each material are shown in the figure. A fixed support is rigidly attached to the right end of the bronze rod. Determine the stress each section in kPa. Aluminum Steel D=28mm D=20mm 20KN Bronze D=25mm 150KN
Problem 5: A rigid bar of negligible weight is supported as shown in Figure. If W = 100 kN, a) compute the temperature change that will cause the stress in the steel rod to be 60 MPa. Assume the coefficients of linear for steel and 18.9 μm/(m °C) each rod if the temperature or bronze are 11.7 stress is applied. Steel L = 1.5 m A = 320 mm² 1m E= 200 GPa 2.5 m in B) find the 40°C after a load W = 140 KN Bronze L = 3m A = 1300 mm² E = 83 GPa W 1.5 m-
3. An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminum of 13.05 ksi, or in bronze of 100 MРа. Aluminum A = 400 mm Bronze A = 200 mm Steel A = 500 mm? 2P 4P 2.5 m 2.0 m 1.5 m
Situation 2 For the assembly shown, determine the stress in each of the two vertical rods if the temperature rises 40°C after the load P=50 KN is applied. Neglect the deformation and the mass of the horizontal bar AB. Compute the vertical movement under the load. Steel Aluminum E=200 GPa E=70 GPa L-4m A=300 mm? a-11.7x10*/°C L-3m A=900 mm a=23x10“ /°C 3 m 3 m 3 m Situation 3
A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in the figure given. Axial loads are applied at the positions indicated. If P = 3000 Ib and the cross sectional area of the rod is 0.5 in?, determine the stress in each section. 4P Steel Bronze Aluminum P 2 ft 3 ft 2.5 ft
1. An axial force of 250 kN is applied to the assembly shown, made of cylindrical brass core surrounded by an aluminum shell. The axial force is applied through rigid end plates. a) Determine the normal stress in each of the metal components, given that Ebrass = 105 GPa and Ealum = 70 GPA. 100mm b) What is the axial deformation of the assembly? 200mm 200mm
An aluminum bar having a cross-sectional area of 160 mm? carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E= 70000 MPa. The length of each bars are follow: B1 0.8 m; B2 = 1.0 m; B3= 0.6 m. Determine the axial stress of bar B1 in MPа. 35KN B1 B2 ВЗ 10KN 15KN 30KN A 218.75 В 125 (c) 62.5 31.25
An aluminum bar having a cross-sectional area of 160 mm carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B; = 0.8 m; B; = 1.0 m; B3= 0.6 m. Determine the axial stress of bar B; in MPa. 35KN B1 B2 B3 10KN 15KN 30KN
Situation 6: The rigid bar of negligible weight is supported as shown in the figure. If W = 120 kN, There is a temperature change occur in the assembly and cause a tensile stress of 55 MPa in the steel rod. Use the following data: Bronze steel 1 m - 2 m O 4 m W 2 m 3 m 16. Compute the axial stress at bronze rod 17. Compute for the change of temperature 18. Compute for the vertical deflection at the W Steel Rod Bronze Rod A (mm²) 320 1500 a (/°C) 11.7 x 10-6 18.9 x 10-6 E (GPa) 200 83
A rigid plate ABCD is subjected to forces as shown in Figure below. Compute the magnitude of the resultant (in KN) of the system with reference to the point A.
A circular steel tube of length L = 59 inches is loaded in torsion by torques T (see the figure). r2 (a) If the inner radius of the tube is ri = 1.35 in. and the measured angle of twist between the ends is p = 0.5°, what is the shear strain y1 (in radians) at the inner surface? Round your answer to nearest whole. x10-6 rad Yi = (b) If the maximum allowable shear strain is 0.0004 rad and the angle of twist is to be kept at 0.5° by adjusting the torque T, what is the maximum permissible outer radius (r2).may? Round to two decimal places. (r2)max in.
The rigid bar of negligible weight is supported as shown in the figure. If W = 80 kN, compute the 2 temperature change of the assembly that will cause a tensile stress of 50 MPa in the steel rod. Use the following data: A (in?) a (/OF) E (GPa) Steel Rod 300 11.7 x 106 200 Bronze Rod 1400 18 x 10-6 83 Bronze 3 m Steel 1.5 m 1.0 m 2.5 m 1.5 m → W