A solid shaft of diameter 30 mm is fixed at one end. It is subjected to a tensile force of 10 kN and a torque of 60 Nm. At a point on the surface of the shaft, determine the principle stresses and the maximum shear stress.

A solid shaft of diameter 30 mm is fixed at one end. It is subjected to a tensile force of 10 kN and a torque of 60 Nm. At a point on the surface of the shaft, determine the principle stresses and the maximum shear stress.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.26P: -26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and...

See similar textbooks

Related questions

Q: etermine the normal stresses in bronze rods (1) and steel rod (2) after

Q: The same torque is applied to two tubes with identical metal sheets, determine the ratio of…

Q: The copper pipe [G = 7,000 ksi] has an outside diameter of 3.875 in. and a wall thickness of 0.250…

Q: A 40-mm diameter hole is drilled 3-m deep into the steel shaft. When the first torque is removed at…

A: Let shear modulus (G) of steel shaft be 83 GPa. The torque in AB and BC portion is -TAB=6000-2000 =…

Q: A pressurized pipe with an outside diameter of 14.35 in. and a wall thickness of 0.25 in. is…

Q: A thin-walled cylinder has an internal diameter of 1200 mm and has walls 1.2 mm thick. It is…

A: For solution refer below images.

Q: 2. A hollow shaft of 30-mm inner diameter and 60-mm outer diameter is acted on by an axial tensile…

Q: A 6" diameter pulley attached to a 1" diameter shaft of 2" length is supporting a load of 2000 lb.…

A: Consider below figure for the given question: We are given, Load = P = 2000 lb Diameter of pulley =…

Q: The propellers of a ship are connected to an A-36 steel shaft that is 60 m long and has an outer…

A: Torque is written as, Polar moment of inertia of shaft is written as,

Q: A 40-mm diameter hole is drilled 3-m deep into the steel shaft. When the first torque is removed at…

Q: A2000-in diameter solid shaft is subjected to an adal force of P=560 Ib, a horizontal shear force of…

Q: A solid 30-mm-diameter shaft is used in an aircraft engine to transmit 86 kW at 1,250 rpm to a…

A: we have to develop principal stress & shear stress

Q: A steel propeller for a windmill transmits 5 kW at 87.9 rpm. If the allowable shear stress in the…

Q: At a point in plane stress the principal stresses were found to be 22 MPa(T) and 14 MPa (C). The…

A: The given data are: σ1=22 MPaσ2=14 MPa Here, σ1 denotes the maximum principal stress and σ2 denotes…

Q: A shaft is made of an aluminum alloy having allowable shear stress of tallow = 100 MPa. If the…

A: Given Allowable shear stress = 100 MPa Diameter of shaft = 100 mm To find Maximum torque at 75 mm

Q: A spherical pressure vessel has an inner radius of 5 ft and a wall thickness of 0.5 in. Draw Mohr’s…

A: Given data r=5 ftt=0.5 inP=80 psi

Q: The brass wire has a triangular cross section, 2 mm on a side. If the yield stress for brass is tY =…

A: Given Data: Side of triangular section is a =2 mm. Yield stress of shear is tY = 205 MPa. Length of…

Q: An axial tensile load of 10kN is applied to a 12mm diameter bar. Determine the maximum shearing…

Q: A solid 1.500-in.-diameter steel shaft is subjected to torques TB = 255 lb-ft and TD= 95 lb-ft,…

Q: 1.4 kNm C H KI 10 kN 240

Q: A hollow shaft for a rotary compressor is to be designed to transmit a maximum torque of 4750 N-m.…

A: Given data: Maximum torque, T = 4750 N·m. Shear stress in the shaft, τ = 50 MPa. The ratio of…

Q: A1 m long and 35 mm diameter aluminum shaft is to be replaced by a steel hollow shaft of the same…

Q: The shaft assembly is made from a steel tube 1 in. in diameter, which is bonded to a solid brass…

A: Given Data The diameter of the steel tube is: D=1 in The diameter of the solid brass core is: d=0.5…

Q: The 60 mm diameter solid shaft is subjected to the distributed and concentrated torsional loadings…

Q: Two shafts, one of steel and the other of phosphor bronze, are of the same length and are subjected…

A: Answer: (a) The diameter of the phosphor-bronze shaft is 28.12 mm. (b) The ratio of the maximum…

Q: The drive shaft AB of an automobile is to be designed as a thin-walled tube. The engine delivers 150…

Q: A thin circular disk of inner radius a and outer radius b is shrunk onto a rigid plug of radius a +…

Q: The drive shaft AB of an automobile is made of a steel having allowable shear stress of tallow = 8…

A: Given data: Allowable shear stress of the shaft, τallow = 8 ksi. The outer diameter of the shaft,…

Q: A brass rod 8mm diameter and 400mm long fits centrally inside aluminum tube of the same length…

Q: A steel gear, with 80-mm diameter rod connected to it is used to transmit 600 HP at 200 rpm. If the…

A: Given: d = 80 mm H = 600 hp n = 200 rpm

Q: solid circular shaft of diameter 60mm is ojected to an axial stress of 20 MPa. It is ther subjected…

Q: Q2 /A steel shaft transmits 800 kw of power at 210 pm Determine the actual working stress and the…

Q: A steam turbine rotor is 160 mm diameter below the blade ring and 25 mm thick. The turbine is…

A: A steam turbine rotor has a diameter of 160 mm below the blade ring and is 25 mm thick.The turbine…

Q: QUESTION 1. Determine the constant thickness t of the square shaped tube if the average shear stress…

A: Given data: The average shear stress is; ? = 90 MPa. The magnitude of the torque is; T = 3 kNm. The…

Q: A 4-m long shaft transmits a torque of 5 kN-m. Determine the maximum torsional stress (TMax) of the…

A: Given: length of the shaft→L=4m torque transmitted→T=5 KN‐m=5000 N‐m outer diameter of the…

Q: 90 MPa PROBLEM 7.15 30 MPa For the given state of stress, determine the normal and shearing stresses…

Q: A 40-mm diameter hole is drilled 3-m deep into the steel shaft. When the first torque is removed at…

Q: A1 m long and 35 mm diameter aluminum shaft is to be replaced by a steel hollow shaft of the same…

A: When torque is applied on the shaft, then only shear stresses are produced which acts in two…

Q: A belt pulley is fastened to a 7.46125 shaft, running at 200 rpm, by means of a key 19.05mm wide…

Q: With the same given, if the members have a square cross-section with a diagonal of 11.31 cm and…

A: In the question, the applied magnitude of force is not given, thus it is not possible to calculate…

Q: A hollow shaft for a rotary compressor is to be designed to transmit a maximum torque of 4750 N-m…

A: Given data Maximum torque (T) = 4750 N-m limited shear stress (τ) = 50 MPa Inside dia to outside…

Q: A helicopter's rotor shaft has the hollow circular cross section shown as follows. The shaft is…

A: Calculated principal stress and absolute maximum shear stress at point p.

Q: For a given maximum average shear stress, determine the factor by which the torque-carrying capacity…

A: The mean area without reversed position Am=(1.10)1.75-π(0.55)22=1.4498 in2 The mean area at reversed…

Q: Determine the diameters of a hollow shaf

Q: If P is equal to 125 kN Determine the normal stresses of members DH & HG in kPa. The diameter of…

A: Given data, P= 125 KN Diameter d= 120 mm = 0.12 m Cross section area = A= 0.25*π*d² = 0.01131 m²

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
A thick cylinder of 150 mm outside radius and 100 mm inside radius is subjected to an external pressure of 30 MPa and internal pressure of 60 MPa. Calculate the maximum shear stress in the material of the cylinder at the inner radius
A body is subjected to a direct tensile stress of 300 MPa in one plane accompained by a simple shear stress of 200 MPa. Determine maximum normal stress on the plane.
A solid 1.10 in. diameter shaft is subjected to a torque of T = 390 lb-ft and an axial load of P = 4900 lb. (a) Determine the principal stresses and the maximum shear stress at point H on the surface of the shaft. (b) Show the stresses of part (a) and their directions on an appropriate sketch. Answer: (a) Op1 = i %p2 = i Tmax in-plane i H (1) psi psi psi T B P X (b) Show the stresses of part (a) and their directions on an appropriate sketch.
A hollow shaft with an outside diameter of 113 mm and an inside diameter of 103 mm is subjected to both a torque of T= 6.2 kN-m and an axial tension load of P = 106 kN, as shown. Determine the normal and shear stresses at point H and show them on a stress element. y (1) Answers: Ox = i MPa, oy = i MPa, Txy = i MPa.
A hollow shaft with an outside diameter of 3.2 in. and an inside diameter of 2.6 in. is subjected to both a torque of T = 614 lb-ft and an axial tension load of P = 7410 lb, as shown. (a) Determine the principal stresses (σp1 > Op2) and the maximum shear stress Tmax at point H on the surface of the shaft. (b) Show the stresses of part (a) and their directions in an appropriate sketch. H (1) I X B
Two shafts, one of steel and the other of phosphor bronze, are of the same length and are subjected to equal torques. If the steel shaft is 25 mm diameter, find the diameter of the phosphor-bronze shaft so that it will store the same amount of strain energy as the steel shaft. Also determine the ratio of the maximum stear stresses induced in the two shafts. Take the modulus of rigidity for phosphor bronze as 50 GN/m² and for steel as 80 GN/m².
A hollow shaft with an outside diameter of 3.1 in. and an inside diameter of 2.8 in. is subjected to both a torque of T = 525 lb-ft and an axial tension load of P = 6840 lb, as shown. (a) Determine the principal stresses (0p1> 0p2) and the maximum shear stress Tmax at point H on the surface of the shaft. (b) Show the stresses of part (a) and their directions in an appropriate sketch. Answers: %p1= i 1 op2= Tmax psi. psi. psi.
The same torque is applied to two tubes with identical metal sheets, determine the ratio of Tcircle/Tsquare of the shear stresses. Given: r = 15 mm, S = 22 mm, and t = 2.91mm.
The cross section of the rod in the picture is a circle with a diameter of 24 mm. The rod is pulled with a force of N = 20500 N, in addition to which a torque of T = 100 Nm acts. Determine the von Mises reference stress at point A on the outer surface of the rod. Note that it appears that the stress distributions caused by the normal force remain constant over the entire length of the beam! A plane stress state can be assumed at the point under consideration. Use units [N, mm] for calculations Please enter an answer to one decimal place. Do not round off the invoices in the intermediate stages, but only the final answer!