An axial tensile load of 10kN is applied to a 12mm diameter bar. Determine the maximum shearing stress in the bar and the plane on which it acts. Find also the value of the normal stresses on these plane

Q: Neglecting the weight of the bracket, calculate the three principal stresses, and absolute maximum…

A:

Q: Oy Txy

A: given; normal stress in x direction =σxnormal stress in y direction =σyshear stress in xy…

Q: Figure shows that a hole must be drilled in a plate with a shear strength of 40 ksi. Compressive…

A:

Q: The major and minor principal stresses are 3 MPa and -3MPA respectively. The maximum shear stress at…

A: Given data : Major principal stress=3 MPaMinor principal stress=-3 MPa

Q: Two wrenches are used to tighten the pipe. The pipe is made from a material having an allowable…

A: The maximum allowable shear stress is The outer diameter of pipe is The inner diameter is

Q: A 1500N force is applied to a bracket as shown. The diameter d = 25mm, determine the principal…

A:

Q: Neglecting the weight of the bracket, calculate the three principal stresses, and absolute maximum…

A:

Q: Construct a Mohr's circle for the following point stresses: o = 60MPa, oy = 10MPa and Txy = +20MPa,…

A:

Q: The cylinder for a hydraulic press has an inside diameter of 300 mm and an outside radius of 260 mm.…

A: Inside diameter = 300 mm Inside radius = 150 mm outside radius = 260 mm internal pressure = 80 Mpa

Q: For part d, we introduce a wall at cross-section A. Determine the absolute maximum shear stress on…

A:

Q: HWs. 1. The grains of wood in the board make an angle of 20° with the horizontal as shown. Using…

A: As per given question  Axial load=250N Angal=20° Width=25mm Thickness=60mm We have to draw mohr…

Q: Q.1:Answer only one from a & b: a: At a certain point in a stressed body, the stresses are ox= 30…

A: Given: The stress on the x phase is σx=30 MPa The stress on the y phase is σy=-25 MPa The shear…

Q: A differential stress element has the following stress components: Ox = 20 ksi, y = -10 ksi, Txy =…

A:

Q: Two bars are connected by means of a rivet of diameter 5 mm as shown in fig. below. Determine the…

A:

Q: wood grains on the board shown below form an angle of 20° with the horizontal. using the circle of…

A: Given data,axial load=250N

Q: A 6" diameter pulley attached to a 1" diameter shaft of 2" length is supporting a load of 2000 lb.…

A:

Q: Consider the stress element below. (a) Determine the three principle stresses and three shear…

A:

Q: Q-5 Wall thickness of a thin cylinder shell of 800 mm internal diameter is 10 mm. length of the…

A: internal diameter of cylinder(d)=800 mm=0.8mwall thickness(t)=10m=0.01minternal pressure…

Q: A thin cylinder of 100 mm internal diameter and 5 mm thickness is subjected to an internal pressure…

A: Introduction: Internal pressure causes a hoop and longitudinal tension in a thin-walled tube or…

Q: |F 2F a 3F| b a

A:

Q: The forces 011, 022, 033, 012 and 021 are acting at a point of an elastic body (023 = 031 = 0). Find…

A: Given: σ23=σ31=0 Solution: The stress  tensor on the elastic body can be written as :…

Q: = A machine component is fabricated from a bent tube as shown below. One part of the tube lies along…

A: Outside diameter, d0=122 mmInside diameter, di=108 mmForce F=8.5 kNLengths,L1=258 mmL2=118 mmL3=281…

Q: For the shown element, what are the principal stresses and their orientations (ew, cew), draw the…

A: (a) To find: The principle stress and the orientation of principle stress Given: The stress in…

Q: Find the stresses at points A and B on the plate shown in the figure.

A: The normal stress on the point A can be determined as,

Q: 1. Calculate the maximum stresses to occur in the hole and groove (groove) areas in the plate below,…

A: Given, Applied load (F)=5000N Width of the plate=200mm The thickness of the plate (t)= 25mm Diameter…

Q: Q.1:Answer only one from a & b: a: At a certain point in a stressed body, the stresses are o, 400…

A: Given: The stress on the x plane is σx=400 MPa The stress on the y plane is σy=-300 MPa The shear…

Q: Electrical strain gauges were applied to a notched specimen to determine the stresses in the notch.…

A: Given:Strain along the x-axis, εx=0.0019Strain along the y-axis, εy=-0.00072

Q: Q.1:Answer only one from a & b: a: At a certain point in a stressed body, the stresses are o, 400…

A: The stress on the x plane is σx=400 MPa The stress on the y plane is σy=-300 MPa The shear stress on…

Q: A pipe has an outside diameter of 0.7 inches and inside diameter of 0.12 inches. A force of 411 lbs…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.