A solid circular shaft of diameter d and length L isfixed at one end and free at the other end. Atorque T is applied at the free end. The shearmodulus of the material is G. The angle of twist atthe free end isOO16TLПd¹G32TLПd4G64TLПd¹G128TLПd¹G

Answered: Image /qna-images/answer/cef9ffe0-6ec4-4a80-aed9-bc49b4c9f013.jpg

Answered: A solid circular shaft of diameter d…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rigid bar ABCD supports point loads at A and D and is being supported by two bars at B and C. Determine the absolute value of the deformation at point C. (in mm) 120KN 4m 3m Sm A 90 kN L3 6m A= 0.04 m A = 0.06m² E=200 6AE=80 GPa L-4m
A thin polymer plate PQR is deformed so that corner Q is displaced downward by a distance L = 1.45 mm to new position Q' as shown. Determine the shear strain at Q' associated with the two edges (PQ and QR). 120 mm 480 mm. P R 240 mm -2692 μrad -3352 μrad O-4917 prad -3610 μrad O-2921 urad Q 'Q' X
Problem 3 Determine the maximum ram force P that can be applied to the clamp at D if the allowable normal stress for the material is oallow 200 MPа 10 mm 40 mm a a 60 mm 10 mm 200 mm
The rigid bar ABCD supports point loads at A and D and is being supported by two bars at B and C. Determine the absolute value of the deformation at point C. (in mm) 120KN 4m 3m Sm A L= 6m 90 kN L-4m A= 0.04m A = 0.0 Gm² E=200 GA E=80 GPa
100kN B (EA is constant) A 60KN + Determine the Force in member 4m D BD) se Force method (Consistent deformation) 3 m
3) The rigid link is supported by steel wire (1) with an unstretched length of 200 mm and cross-sectional area of 22.5 mm?. Member (2) is a short aluminum of initial length 50 mm and cross-sectional area of 40 mm?. The modulus of elasticity of the steel wire is 200 GPa and the aluminum block is 70 GPa. a) Draw the deflected shape of the rigid member and clearly label the deformation of members (1) and (2). b) Write the equilibrium and compatibility equations needed to solve the problem along with the supporting sketches. Hint: Be sure to carefully consider if the members are elongating or shortening; this must be represented mathematically. c) Calculate the internal forces in both axial members and clearly indicate tension or compression. [Ans. to Check: F2 = 535 N]
The rigid beam is supported by a pin support at A and steel wires BD and CE (E-200GPA). Solve the ratio between the deformations of wire CE and wire BD. 4 m 3 m 2 m 2 m O 7/3 O 7/4 O 7/5 O 7/2
Q1: A torque T = 4 kN.m G of steel core 77 GPa and G of aluminum 27 GPa. Determine: (a) maximum shearing stress in the in the steel core. (b) the maximum shearing stress in the aluminum jacket. (c) the angle of twist at A. 172 mm 54 mm- A Steel core- 25 m Aluminum Q2: aluminum rod AB (G=27GPa) brass rod BD (G= 39GPa). portion CD of the brass rod is hollow and has an inner diameter of 40 mm, Determine: a) the angle of twist at A. b) maximum shear stress of rod AD c) torque diagram d) angle of twist diagram 60 mm TB 1600 Nm 36 mm T₁ = 800 Nm. 400 mm q+ 375 mm 250 mm
SITUATION 31 Consider the system above. A rubber is used to bond a solid steel shaft (Diameter = 130mm) to another steel pipe (Diameter=200mm), fixed on the ground. A simple lever is used to test the bond between the two caused by the rubber. Bar AC has a length of 3m, a pin at B is used as the fulcrum of the system. Pin at B has allowable shearing stress of 100 MPa, the rubber has modulus of elasticity of 4.2 MPa and Poisson's ratio of 0.42. Consider deformation on rubber only, and pin at B experiencing double shear. 2000 100. A D-lémm 1. Determine the maximum vertical displacement of the shaft to not exceed the working shearing stress of the pin at B. 2. Considering Pin at B will not collapse. Determine the required force P to lift the shaft 5mm from the ground 225 00. 130
In the following structure, consider the following data: The connection at D is double and has a diameter of 50 mm. The beam BCDE has a thickness of 37.50 mm. The bar AB has a thickness of 37.50 mm and a width of 100. The connection at A is single and has a diameter of 67.50 mm. a. The normal stress in bar AB. Answ. 3.53 MPa b. The shear stress in the bolt at D. Answ. 6.25 MPa c. The shear stress in the bolt at A. Answ. 6.25 MPa d. The support stress between the beam and bolt D. Answ. 13.08 MPa
THE DIAGONAL MEMBERS IN THE CENTER PANELS OF THE TRUSS SHOWN ARE VERY SLENDER AND CAN ACT ONLY IN TENSION; SUCH MEMBERS ARE KNOWN AS COUNTERS. DETERMINE THE FORCE IN MEMBER DE AND IN THE COUNTERS THAT ARE ACTING UNDER THE GIVEN LOADING. (15 PTS) Counters ARA B F 6 ft H C E G 3 kips 6 kips 9 kips -S ft- <8 ft- S ft→|<-S ft-
Find the maximum bending stress 3 N/m o-8 cm a-2 cm 3 N/m Im t Im 2 Cm

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

A solid circular shaft of diameter d and length L is fixed at one end and free at the other end. A torque T is applied at the free end. The shear modulus of the material is G. The angle of twist at the free end is O O 16TL Пd¹G 32TL Пd¹G 64 TL Пd¹G 128TL Пd¹G