A solid 4340 HR Steel tie rod of length Lrod = 950 mm is employed to compress à 6061-T6 aluminum bushing of length Lbushing = 650 mm as shown. The tie rod has a solid circular cross section with diameter drod = 27.5 mm. The bushing has a hollow circular cross section with outer diameter do = 80 mm, inner diameter di, and wall thickness t. If F = 47.5 kN, determine the minimum wall thickness of the bushing based on the below design requirements: ⚫the displacement of the bottom of the tie rod with respect to the fixed horizontal surface may not exceed Stotal = 1.1 mm • the normal stress of the bushing may not exceed the yield strength of the bushing material Rod cross section О drod Lbushing d Lrod drod FL Bushing cross section do

A solid 4340 HR Steel tie rod of length Lrod = 950 mm is employed to compress à 6061-T6 aluminum bushing of length Lbushing = 650 mm as shown. The tie rod has a solid circular cross section with diameter drod = 27.5 mm. The bushing has a hollow circular cross section with outer diameter do = 80 mm, inner diameter di, and wall thickness t. If F = 47.5 kN, determine the minimum wall thickness of the bushing based on the below design requirements: ⚫the displacement of the bottom of the tie rod with respect to the fixed horizontal surface may not exceed Stotal = 1.1 mm • the normal stress of the bushing may not exceed the yield strength of the bushing material Rod cross section О drod Lbushing d Lrod drod FL Bushing cross section do

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.7.10P: Three round, copper alloy bars having the same length L but different shapes are shown, in the...

See similar textbooks

Similar questions

Solve Problem 11.3-3 for a W 10 × 45 steel column having a length L = 28 ft.
4) Ball bearings support the rotating axle shown below at points A and D. The rotating axle is loaded by a stationary (non-rotating) force of F = 6.8 kN. In the drawing below, all dimensions are in mm, and all geometry changes (steps in the diameter shaft) have a fillet radius of 3 mm. The axle is machined from AISI cold-drawn steel with an ultimate strength of S_u = 690 MPa and a yield strength of S_y= 580 MPa. Calculate the safety factor at the 6.8 kN load and points B and C, which experience moderate bending moments with a geometric feature that causes a stress concentration. Determine the number of cycles to failure of this part. 30 -10 -250 32 B 6.8 KN 75 -38 100- с 125 10 35 D 30
A solid square rod is cantilevered at one end. The rod is 0.8 m long and supports a completely reversing transverse load at the other end of 50 kN. The material is AISI 1060 hot-rolled steel (sy = 370 MPa, Su = 680 MPa). Use a design factor of 2 and determine the dimensions of the square cross section for the following cases. Consider all possible endurance limit modifying factors. Neglect any stress concentration. a. The rod must support this load for 100 cycles.
A flanged bolt coupling is used to connect a solid shaft 90 mm in diameter to a hollow shaft 100 mm in outsude diameter and 90 mm in inside diameter. If the allowable aring stress in the shafts and the bolts is 60 MPa, how many 10 mm diameter steel bolts must be used on a 200 mm diameter bolt circle so that the coupling will be as strong as the weaker shaft?
The sbaft shown overhangs a bearing on the right and has the following dimensions: a - 5 in., b - 4 in., and - 10 in. The material is AISI C1040. annealed. This shaft is subjected to a torque T 10,000 in-lb., forces F - 10,000 lb. and F, 20,000 lb. Using a atatio-design approach, determine the diameter D for N 2.5, with eomputa- %3D Answer: a) Dia. = _inches %3D %3D %3D tions from the maximum shear stress theory. Note: Use Sy = 48,000 psi F2 N M
Bearing stress 4. Please provide proper discussion and illustration also complete solution and clear solution please thank you Determine the length of a square key to be used for a 3.73 kW, 1800 rpm electric motor if the motor shaft diameter is 35 mm and the width of the key is approximately one-fourth of the shaft diameter. The allowable shearing stress on the key is 2.45 MPa
Agui - 4550/2 =2276 two plates each with thickness t - 16 mm are bolted together with 6-222 mndia. bolts firming alap Joint Bolt spacing are follows St- $40mm S2 - 80mm, S3=150mm effective bolt hole dia. is 25mm A36 is used. Compute the allowable tensile Strength P t = 16 mm &t 52 747₁ 0 O O 40 60 80 40 +=16mm S-400 $3-100 S2-40 7 @ 4umm P
1) Ball bearings support the rotating axle shown below at points A and D. The rotating axle is loaded by a stationary (non-rotating) force of F = 6.8 kN. In the drawing below, all dimensions are in mm. While the real part has fillets (r=3mm), you can assume an abrupt change in geometry for each shaft step for this problem. The axle is machined from AISI cold-drawn steel with an ultimate strength of S_u = 690 MPa, a yield strength of S_y=580 MPa, and a modulus of Elasticity of E_steel = 207 GPa. Determine the displacement at the 6.8 kN load and points B and C. 6.8 KN 30 10 250 32 B 75 38 100 10-1 -35 30
Design the rectangular key which is located on the shaft motor if the diameter of it Is ( 48 ) mom and shearing and crushing stresses which applied of it are ( 420 ) Nimm and ( 700 ) N / mm' respectively , when the force applied on the key equal to ( 8 000 ) N ? jo 5:18 /
The solid spindle AB has a diameter ds=40mm and is made of a steel with G=110GPa and Tem=120MPa , while sleeve CD is made of a braa with G=256GPa and Tem=70MPa. Determine the angle through end A can be rotated.
A transmission shaft supporting a helical gear B and an overhung bevel gear D is shown in Fig. bearings, A and C. The pitch circle diameter of the helical gear is 450 mm and the diameter of the bevel gear at the forces is 450 mm. Power is transmitted from the helical gear to the bevel gear. The gears are keyed to the shaft. The material of the shaft is steel 45C8 The factors k, and k, of ASME code are 2.0 and 1.5 respectively. Determine the shaft diameter using the ASME code. 400 The shaft is mounted on two 400 400 270 250 210 640i ]640 100
The flange coupling for two shafts made of plain carbon steel to be   connected. The shafts transmitting a toque of 600 N-m. Assume the following   permissible stresses for the coupling components: Shaft — Permissible shear stress = 35 MPa Keys — Rectangular formed end sunk key having permissible compressive strength = 60 MPa Bolts — Six numbers made of steel having permissible shear stress = 28 MPa Pitch circle diameter of bolts = 1.6 × Diameter of shaft   1. diameter of shaft =44.36 2. Hub length =67.5 3. Hub diameter 90 mm Calculate: 2. thickness of flange; 3. Diameter of flange 4. Width of key 5. Thickness of key 5. Diameter of bolt; 6. Crashing stress in bolt