A circular duct carrying water gradually contracts from a diameter of 30cm to 15cm. The figure (not drawn to scale) shows the arrangement of differential manometer attached to the duct. 30 cm V₁ 18 cm 15 cm Mercurry When the water flows, the differential manometer shows a deflection of 8cm of mercury (Hg). The values of specific gravity of mercury and water are 13.6 and 1.0, respectively. Consider the acceleration due to gravity, g = 9.81 m/s². Assuming frictionless flow, the flow rate (in m³/s, round off to 3 decimal places) through the duct is

A circular duct carrying water gradually contracts from a diameter of 30cm to 15cm. The figure (not drawn to scale) shows the arrangement of differential manometer attached to the duct. 30 cm V₁ 18 cm 15 cm Mercurry When the water flows, the differential manometer shows a deflection of 8cm of mercury (Hg). The values of specific gravity of mercury and water are 13.6 and 1.0, respectively. Consider the acceleration due to gravity, g = 9.81 m/s². Assuming frictionless flow, the flow rate (in m³/s, round off to 3 decimal places) through the duct is

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Summative Assessment - Geometric Method Determine the Deflection at D. Use the Any Geometric Method (once for DIM, once for AMM, once for CBM) E= 200 GPa, lan = 250x10* mm" leco = 200x10* mm". Distances are in meters. Show complete Solutions 8 kN 6 kN 15 kN/m K Tachnalagy Dutn by fanantien Input your answer in two decimal places. Units in millimeters. No need to write down the units. Just input the numerical value with the sign. Example: if your final answer is 2.11mm upwards, just key-in 2.11 then if your final answer is 2.11mm downwards, key-in -2.11
Question 39/50 Situation 39, 40 10m/s Es=200 GPa E,=105 GPa 50 kg Steel 15 mm-diaBrass k=25 kN/mm 图的的 1.5m 1.5m 0.5m O Zoom image Determine the stiffness of Spring, Steel and Brass assembly as shown. O 8256.25 N/mm O 9141.75 N/mm O 2563.23 N/mm 5632.20 N/mm PreviouIS Next >
Calculate the distance between the instrumentand the staff if the staff readings are 1.56 m, 2.05 m and 2.56 m. The multiplying constant is 100and additive constant is 10.
100 and C = 2) A transit with a stadia interval factor of K = at point C on the line between points A and B,and the following stadia readings were observed: 0.381 was set Vertical Hair Readings(m) Position of Rod angle() -7.14 Middle Upper 1.540 1.960 Lower Rod held at A Rod held at B 1.395 1.250 12.28 1.800 1.640 Determine the following: a) length of line AB b)difference in elevation between points A and B
A 55°25' D S 80°21'E N 85°31'W B S 6°19'E C For the accompanying figure, what is the deflection angle at B? a. 75 degrees 20 minutes R O b. 75 degrees 02 minutes R O c. 75 degrees 02 minutes L O d. 75 degrees 20 minutes L
Situation XII: Water is being raised from reservoir A to reservoir B using pump as shown. The frictional losses from reservoir A to the entrance of the pump is three times its velocity head while the frictional losses from the exit of the pump to reservoir B is twenty times its velocity head. The total flow is 20li/s. El. 240 m El. 0 A 100 mm 150 mm El. - 20 1 2 35. Compute the output power of the pump in kilowatts. a. 68.7 b. 34.0 C. 55.5 С. d. 48.4 36. Compute the pressure head at point 1. a. 19.74 m b. 28.14 m c. 23.51 m d. 48.4 m 37.Compute the pressure head at point 2. a. 233.54 m b. 276.58 m C. 281.42 m d. 266.27 m
Determine the average stadia interval factor of an optical instrument below. C = 0. Distance of Rod from Instrument 30 m 60 90 Upper Stadia Hair Reading 1.10 Lower Stadia Hair Reading 1.38 Point A В 1.25 1.70 C 1.30 1.40 1.98 2.30 120 150 180 E 1.58 1.70 2.45 2.60 F
A tacheometer with a stadia constant of 0.30m, and stadia interval factor of 100, was set up on the line between two points A and B. The following hair readings were observed. ROD HAIR READINGS ... POSITION UPPER MIDDLE LOWER Rod held at A 1.327m 1.171m 1.011m Rod held at B 2.004m 1.867m 1.707m If the instrument height is 1.43m and it is set up on a point with elevation 14.72 m, determine the elevation of A.
From the figure shown below: |-100 mm--100 mm-–150 mm - 150 mm 150 mm 75 mm 1. Determine the distance of the centroid from the x axis. 450 x10^6 2. Determine the moment of inertia of the shaded area about the x axis. a a. 1.72 x109 mm4 b. 3.23 х109 mm4 c. 2.46 x109 mm4 d. 4.11 x109 mm4 e. none of the above 3. Determine the moment of inertia of the shaded area about the y axis. c a. 1.09 x109 mm4 b. 3.71 х109 mm4 2.03 x109 mm4 d. 4.83 x109 mm4 С. e. none of the above
A tacheometer fitted with an anallatic lens was used to observe the following:InstrumentStation W.C.B Staff Station VerticalAngle Staff Readings(m) C 320 0 A -12 0 0.906, 1.728, 2.550C 50 0 B + 10 0 0.744, 2.199, 3.654The value of the constant was 653and the staff was held vertically. Determine thelength R.L of A & B and gradient of AB
Load (N) Deflection (mm) 0 0 4.903034 0.000346 11.416539 0.000802 18.337648 0.001251 25.050375 0.001727 29.707962 0.002173 31.75 0.002634 29.888114 0.003094
äbäi 25 Q1) A particle moves on X-Y coordinate system. It starts from X1 = -8m then moved to X2 = 14m, then it came back to the original point and moved 16m on the y-axis. What is the ?total distance and net displacement جابتك